(8.00 to 75.00 lbf.ft) 0U190360 1 PIN - RIGGING 0U190834 1 TOOL - ZERO POSITIONING, THS ACTUATOR 98D27407502000 1 SUPPORT STRUT - R/I THS ACTUATOR
R 98D27409006000 1 WRENCH-THS GROOVE NUT R 98D27409007000 1 WRENCH-THS GROOVE NUT 98D27903500000 2 PIN-SIDE STICK LOCKING

 B. Consumable Materials

 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
R Material No. 04-004  USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
2 washer retainer 55-16-36 01 -020A 5 washer retainer 55-16-36 01 -050A
 D. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
27-44-00-710-003  Operational Test of the Trimmable Horizontal Stabilizer Actuator with both (Green and Yellow) and Individual Hydraulic Systems
 27-44-51-400-001  Installation of the Trimmable Horizontal Stabilizer
 (THS) Actuator (9CE)
 29-10-00-864-001 Depressurize the Green Hydraulic System
 29-10-00-864-002 Depressurize the Yellow Hydraulic System
 29-10-00-864-003 Depressurize the Blue Hydraulic System
 55-16-34-991-002 Fig. 401

 3. Job Set-up
__________
 Subtask 55-16-34-860-052
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the horizontal stabilizer pitch trim control is set to zero.

 (2)
 Make sure that the hydraulic systems are depressurized. (Ref. TASK 29-10-00-864-001) (Ref. TASK 29-10-00-864-002) (Ref. TASK 29-10-00-864-003).

 (3)
 Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in the CAPT and F/O side stick controllers.

 (4)
 Make sure that the warning notices are in the flight compartment to tell the persons not to operate the flight controls.

 (5)
 Make sure that the warning notices are in position to tell the persons not to operate the hydraulic systems.

 (6)
 Make sure that access platform/3.0 m/(9ft. 10in.) are in position at zones 311/312.

 (7) Make sure that the access door 312AR is open.
 Subtask 55-16-34-865-054

 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11
 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16
 4. Procedure
_________
 (Ref. Fig. 401/TASK 55-16-34-991-002)
 Subtask 55-16-34-420-050
 A. Install the Attach Fittings Bearigns of the THS actuator.
 (1)
 Put the bush (3) in position.

 (2)
 Put a new washer retainer (2) in position.

R (3) Install the nut retainer (1) with the WRENCH-THS GROOVE NUT R (98D27409007000) and toque to between 2.8247 and 3.9546 m.daN (20.83 and 29.16 lbf.ft).
 (4)
 Apply COMMON GREASE (Material No. 04-004) to the bearing (4) and install.

 (5)
 Put a new washer retainer (5) in position.

R (6) Install the nut retainer (6) with WRENCH-THS GROOVE NUT R (98D27409006000) and torque to between 2.8247 and 3.9546 m.daN (20.83 and 29.16 lbf.ft).
 (7) Safety the nut retainer (6) with the washer retainer (5) and the nut retainer (1) with the washer retainer (2).
 NOTE : In the RH of the attach fitting, the bearing (4) must have
____ free movement and the washer retainer (5) must not have any clearance.
 NOTE : In the LH of the attach fitting, the bearing (4) must not have
____ any movement and the washer retainer (5) must have clearance.
 Subtask 55-16-34-410-052
 B. Install the THS Actuator
 (1) Install the primary lower attachment of the THS actuator (Ref. TASK 27-44-51-400-001)
 5. Close-up
________
 Subtask 55-16-34-081-051
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(41)