Fig. Electrical Connections.
Figure 401/TASK 55-10-11-991-001
1EFF : ALL 1 55-10-11 Page 406
1 1 Feb 01/98
1 1
1CES 1
Fig. Bonding Connections.
Figure 402/TASK 55-10-11-991-002
1EFF : ALL 1 55-10-11 Page 407
1 1 Feb 01/98
1 1
1CES 1
Fig. Hydraulic Connections.
Figure 403/TASK 55-10-11-991-003
1EFF : ALL 1 55-10-11 Page 408
1 1 Feb 01/98
1 1
1CES 1
Trimmable Horizontal Stabilizer Sling.
Figure 404/TASK 55-10-11-991-004
1EFF : ALL 1 55-10-11 Page 409
1 1 Feb 01/98
1 1
1CES 1
CAUTION : YOU MUST ALWAYS PUT CAPS ON DISCONNECTED HOSES AND FITTINGS. IF
_______
YOU DO NOT DO THIS, YOU MAY CAUSE:
-CONTAMINATION OF THE HOSES,
-DAMAGE TO THE SYSTEM COMPONENTS,
-HYDRAULIC FLUID LEAKS.
IF HYDRAULIC FLUID LEAKS OCCUR OR IF YOU LET HYDRAULIC FLUID
FALL, YOU MUST CLEAN IT UP IMMEDIATELY. HYDRAULIC FLUID CAN
CAUSE DAMAGE.
(1)
Disconnect the flexible hoses (38) and (39).
(2)
Put hydraulic blanking caps on the disconnected hose ends.
(3)
Remove the unwanted hydraulic fluid (Ref. TASK 51-00-00-615-002). Subtask 55-10-11-010-050
D. Remove Struts
(1)
Remove the diagonal support struts (Ref. TASK 53-53-11-000-001). Subtask 55-10-11-010-051
E. Remove Support Fittings
(1) Remove the THS support fittings at the pivot points of the horizontal stablizer (Ref. TASK 53-56-11-000-001).
Subtask 55-10-11-010-052
F. Remove Trimmable Horizontal Stabilizer
(1) Disconnect the lower attachment of the THS actuator (Ref. TASK 27-44-51-000-001)
(2) Move THS clear of aircraft and lower onto the THS support cradle. Subtask 55-10-11-942-050
G. Remove Support Equipment R (1) Remove the SLING-THS (98D55109005000).
TASK 55-10-11-560-001
Preparation for Installation
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific crane
No specific CRANE
98D27903500000 1 PIN-SIDE STICK LOCKING
R 98D55109005000 1 SLING-THS
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System
3. Job Set-up
__________ Subtask 55-10-11-860-053
A. Aircraft Maintenance Configuration
(1)
Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).
(2)
Make sure that the PIN-SIDE STICK LOCKING is in the CAPT and F/O side stick controllers.
(3)
Make sure that the warning notices are in position in the flight compartment to tell persons not to operate the flight controls.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(13)
