-
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint free cloth No specific non metallic scraper 98D27903500000 4 PIN-SIDE STICK LOCKING

 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 05-013 D TV-53-3507/73 RELEASE AGENT (OBSOLETE USE 05-013A) (Ref. 20-31-00) Material No. 09-005 USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00)
R Material No. 09-016  USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
 Material No. 11-008
 (USE 11-008A) (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
23-61-41-400-001 Installation of the Static Discharger
 29-10-00-864-001 Depressurize the Green Hydraulic System
 29-10-00-864-002 Depressurize the Yellow Hydraulic System
 29-10-00-864-003 Depressurize the Blue Hydraulic System
 MM 55000049000100
 55-14-11-991-001 Fig. 401

 3. Job Set-up
__________
 Subtask 55-14-11-860-051
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the horizontal stabilizer is safe (Ref. MM 55000049000100)

 (2)
 Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).

 (3)
 Make sure that the PIN-SIDE STICK LOCKING is in the CAPT and F/O side stick controllers.

 (4)
 Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controls.

 (5)
 Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.

 (6)
 Make sure that the access platforms are in position at zone 332 and/or zone 342.

 Subtask 55-14-11-865-054
 B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16
 4. Procedure
_________
 (Ref. Fig. 401/TASK 55-14-11-991-001) Subtask 55-14-11-110-051
 A. Prepare the Tips for Installation
 (1)
 Use a non metallic scraper to remove the old sealant from the mating surfaces of the tip, the rib and the upper and the lower shell.

 (2)
 Use CLEANING AGENTS (Material No. 11-008) and clean lint free cloth to clean the component and the interface

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 Subtask 55-14-11-420-052
 B. Installation of the THS Tips 332AB (342AB) NOTE : The installation of the left tip 332AB is shown. The installation
____
 of the right tip 342AB is the same.

 (1)
 Apply SEALANTS (Material No. 09-005) to the mating surfaces of the tip, the rib and the upper and lower shell.

 (2)
 Apply SPECIAL MATERIALS (Material No. 05-013) to the mating surfaces of the tip.

 (3)
 Put the tip (2) in position on the THS.

 (4)
 Install the screws (1) and tighten. Subtask 55-14-11-914-051

 C. Sealing

 (1)
 Apply SEALANTS (Material No. 09-016) to the gap around the tip. Subtask 55-14-11-420-051
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(29)