Inspection Areas-Elevator Figure 601/TASK 55-20-00-991-001
1EFF : 1 1R 1CES ALL 1 11 1 55-20-00 Page 605 Feb 01/04
Subtask 55-20-00-270-050
R B. Resonance Frequency Inspection
R R R (1) Make a special detailed inspection of the elevator top and bottom skin panels in the areas of the hinge supports 2, 3 and 4 and the actuator fittings 1 and 2 for delamination (Ref. NTM 552004 PB 501).
(2) Do a damage delamination report of the inspected area.
R (3) If damage is found, look for allowable damage limits (Ref. SRM 552100 PB 101).
5. Close-up________
Subtask 55-20-00-410-052
A. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 55-20-00-942-050
B. Remove Ground Equipment
(1) Remove the warning notice(s).
(2) Remove the access platform(s).
Subtask 55-20-00-081-050
C. Remove Locking Devices
(1) Remove the PIN-SIDE STICK LOCKING for the CAPT and F/O side stick controllers.
(2) Remove the SETTING TOOL-NEUTRAL, ELEVATOR from the elevator.
Subtask 55-20-00-865-051
D. Close Circuit Breakers Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 19CE2, 16CE1, 16CE2, 19CE3, 19CE1, 15CE2
TASK 55-20-00-200-002
R Detailed Inspection of Elevator Panels, Internal Structure as far as visible R
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1. Reason for the Job
__________________
Refer to the MPD TASK: 552005-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific warning notice
No specific warning notices
No specific access platform 3.5 m (11 ft. 6 in.)
98D27309001000 1 TOOL-ELEVATOR NEUTRAL SETTING
98D27903500000 2 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 09-005 USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00) Material No. 11-010 USA TT-I-735 GRADE A ISOPROPYL ALCOHOL (Ref. 20-31-00) Material No. 19-015 USA BMS 8-98 TYPE 3 CLASS 2 POLYVINYL FLUORIDE FILM (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System 29-10-00-864-002 Depressurize the Yellow Hydraulic System 29-10-00-864-003 Depressurize the Blue Hydraulic System 55-13-11-000-001 Removal of the THS Trailing Edge Access Panels 55-13-11-400-001 Installation of the THS Trailing Edge Access Panels
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(56)
