(2)
 Put the warning notices in position to tell persons not to operate the hydraulic systems.

 (3)
 Put the access platform in position at zone 334 for the left hand THS and/or zone 344 for the right hand THS.

 Subtask 55-16-00-010-054
 E. Access
 (1) Open the access panels 334AT, 334BB, 334BT, 334CT, 334DB, 334DT, 334FB, 334HB and/or 344AT, 344BB, 344BT, 344CT, 344DB, 344DT, 344FB, 344HB. (Ref. TASK 55-13-11-000-001)
 1EFF : ALL 1 55-16-00Page 613 1 1 Feb 01/00R 1 1 1CES 1

 4. Procedure
_________

 (Ref. Fig. 603/TASK 55-16-00-991-004)
 Subtask 55-16-00-110-050
 A. Cleaning
 (1) Clean the elevator hinge supports, the attachment fittings and the adjacent structure with CLEANING AGENTS (Material No. 11-002) and a lint-free cloth.
 Subtask 55-16-00-210-056 
R  B. Detailed Inspection 
R R R  (1) Make a detailed inspection of the horizontal stabilizer hinge fittings, support ribs and actuator fittings for the elevator and the adjacent structure for: - delamination, - deterioration of the structure, - scratches, marks and dents, - cracks, - corrosion, - condition of the bearings, - damaged paintwork. gives details. 
R R R (2) If damage is found, look for allowable damage limits (Ref. SRM 551600 PB 101). 
5. Close-up________
 Subtask 55-16-00-916-050
 A. Protective Treatment
 (1) Apply STORAGE PRESERVATION (Material No. 15-005A) STORAGE PRESERVATION (Material No. 15-006) to the outer surfaces of the attachments fittings (Ref. TASK 51-75-13-916-001).
 Subtask 55-16-00-410-056
 B. Visual Inspection
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 INTENTIONALLY BLANK

R 1 1
55-16-00Page 615
1 1 May 01/05 1 1 1CES 1

R  THS Elevator Hinge Supports and Attachment Fittings Figure 603/TASK 55-16-00-991-004- 12 (SHEET 1)
 1EFF : 1 1 1CES  ALL  1 111 55-16-00 Page 616 Feb 01/00

R  THS Elevator Hinge Supports and Attachment Fittings Figure 603/TASK 55-16-00-991-004- 22 (SHEET 2)
 1EFF : 1 1 1CES  ALL  1 111 55-16-00 Page 617 Feb 01/00

 Subtask 55-16-00-410-057

 C. Close Access
 (1) Close the access panels 334AT, 334BB, 334BT, 334CT, 334DB, 334DT, 334FB, 334HB and/or 344AT, 344BB, 344BT, 344CT, 344DB, 344DT, 344FB, 344HB. (Ref. TASK 55-13-11-400-001)
 Subtask 55-16-00-942-053
 D. Remove Ground Equipment
 (1) Remove the warning notice(s).
 (2) Remove the access platform(s). Subtask 55-16-00-810-050
 E. Remove Locking Devices
 (1) Remove the PIN-SIDE STICK LOCKING (98D27903500000) from the CAPT and F/O side stick controllers.
 Subtask 55-16-00-865-058
 F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 19CE1, 19CE2, 19CE3, 15CE1, 15CE2, 16CE1, 16CE2, 21CE1, 21CE2, 21CE3, 22CE.

R  **ON A/C 051-051, 
R  TASK 55-16-00-200-005 
R  Inspection of the Torque Values of the Upper and Lower THS Support Attach 
R  Fittings 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  1. Reason for the Job__________________ 
R  Self Explanatory 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------

R  No specific  warning notices 
R  No specific  access platform 3.5 m (11 ft. 6 in.) 
R  No specific  Torque Wrench : range 0.20 to 3.60 m.daN 
R  (2.00 to 26.00 lbf.ft) 
R  SL90-313-6250  1 TOOL- INSTALLATION, TAB WASHERS STA-LOK NSA5454 
R  SL90-314-6250  1 TOOL - EXTRACTION, TAB WASHERS STA-LOK NSA5454 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(38)