(2)
Make sure that the PIN-SIDE STICK LOCKING is in the CAPT and F/O side stick controllers.
(3)
Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controls.
(4)
Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.
(5)
Make sure that the access platforms are in position at zone 334 and/or zone 344.
4. Procedure
_________
(Ref. Fig. 401/TASK 55-13-11-991-001) Subtask 55-13-11-140-050
A. Cleaning
(1) Remove the old sealant from the mating surfaces of the panels. Use a nonmetallic scraper.
Subtask 55-13-11-110-050
B. Cleaning
(1) Clean the mating surfaces with CLEANING AGENTS (Material No. 11-003) Subtask 55-13-11-210-050
C. Visual Inspection
(1) Make sure that the anchor nuts and the sealing strips (15) are in a good condition.
TASK 55-13-11-400-001
Installation of the THS Trailing Edge Access Panels WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
WARNING : DO NOT GET THE COMPOUND ON YOUR SKIN.
_______
IF YOU DO:
-RUB IT OFF IMMEDIATELY WITH A CLEAN CLOTH
-WASH THE SKIN WITH SOAP AND RINSE WITH CLEAN WATER. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
CAUTION : USE ONLY THE SPECIFIED MATERIALS AND OBEY THE INSTRUCTIONS FROM THE
_______
MANUFACTURERS. OTHER MATERIALS CAN CAUSE DAMAGE TO THE SURFACE
PROTECTION OF THE COMPONENTS AND THE RELATED AREA.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN) 98D27903500000 4 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 05-013 D TV-53-3507/73 RELEASE AGENT (OBSOLETE USE 05-013A) (Ref. 20-31-00) Material No. 09-005 USA MIL-S-81733 CLASS C CORROSION INHIBITIVE INTERFAY SEALANT (Ref. 20-31-00) Material No. 11-008 R (USE 11-008A) (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
29-10-00-864-001 Depressurize the Green Hydraulic System
29-10-00-864-002 Depressurize the Yellow Hydraulic System
29-10-00-864-003 Depressurize the Blue Hydraulic System
55-13-11-991-001 Fig. 401
3. Job Set-up
__________
Subtask 55-13-11-860-052
A. Aircraft Maintenance Configuration
(1)
Make sure that the hydraulic systems are depressurized (Ref. TASK 29-10-00-864-001), (Ref. TASK 29-10-00-864-002), (Ref. TASK 29-10-00-864-003).
(2)
Make sure that the PIN-SIDE STICK LOCKING is in the CAPT and F/O side stick controllers.
(3)
Make sure that the warning notices are in the flight compartment to tell persons not to operate the flight controlls.
(4)
Make sure that the warning notices are in position to tell persons not to operate the hydraulic systems.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(26)
