(b)  
335DB (left) or 345DB (right)

 (c)  
334AT (left) or 344AT (right)

 S 012-122
 (9)  
Remove the section of the beam (which can be removed) of the stabilizer trailing edge (Fig. 201).

 F.
Install the Inboard Elevator Holding Tool, 2TE65B00184 (Fig. 201)

 S 492-123
 (1)  
Install the inboard elevator holding tool to hold the weight of the elevator surface.

 S 032-124

 (2)  
Remove the rod end dual load bolts to disconnect the elevator from the elevator PCP.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-07
 ALL  ú ú 02 Page 204 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 862-011
 (3)  
Use the holding tool to move the inboard elevator to the full up position.

 (a)  
Hold the inboard elevator in the full up position.

 S 862-125
 (4)  
Put the FLT CONTROL HYD POWER TAIL switches, on the P461 Pilots' Overhead Maintenance Panel, to NORM.

 S 862-126

 (5)  
Remove the DO-NOT-CLOSE tag and close these circuit breakers on the P7, Overhead Circuit Breaker Panel:

 (a)  
7E7, L STAB TRIM S/O VLV

 (b)  
7E20, R STAB TRIM S/ VLV

 S 862-127
 (6)  Move the elevator PCP to the fully retracted position.
 NOTE: The PCP will not go into the shipping crate unless it is
____ fully retracted. The PCP can move aft and down on the sling if it is not retracted.
 S 862-128
 (7)  
Put the FLT CONTROL HYD POWER TAIL switches, on the P461 Pilots's Overhead Maintenance Panel, to CUTOUT.

 S 862-129

 (8)  
Open these circuit breakers, on the P7 Overhead Circuit Breaker Panel, and attach DO-NOT-CLOSE tags:

 (a)  
7E7 L STAB TRIM S/O VLV

 (b)  
7E20 R STAB TRIM S/O VLV

 S 862-130
 (9)  
Move the rudders to release the hydraulic pressure.

 G.
Remove the Inboard Elevator PCP (Fig. 202)

 (1)  
Disconnect the hydraulic lines.

 (2)  
Seal the hydraulic lines and ports with caps.

 S 032-015

 (3)  
Disconnect the input control rod (2) from the inboard elevator PCP crank (6).

 S 032-013
 S 032-014
 NOTE: Do not change the adjustment of the input control rod while
____
 you disconnect it.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-07
 ALL  ú ú 01 Page 205 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
1.
 SPECIAL BONDED BOLT

2.
 INPUT CONTROL ROD

6. BELLCRANK 3. NUTPLATE 5. WASHER
2. INPUT
A-A  CONTROL4. NUT
ROD
SEE A
6. BELLCRANK
15. BARREL NUT
14. RETAINER
A
13. TRUNNION
A
WASHER
(4 LOCATIONS)

12. TRUNNION BOLT (4 LOCATIONS)
11. STABILIZER
REAR SPAR

8. ACTUATOR 7. INBOARD
10. TRUNNION  LUG ELEVATORSEE B
9. ACTUATOR
A
20. INNER NUT
19. WASHER
18. OUTER NUT
17. BUSHING
16. BOLT RAM
9. ACTUATOR ASSEMBLY
8. ACTUATOR LUG
B
Inboard Elevator Power Control Package Installation
Figure 202

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-07
 ALL  ú ú 01 Page 206 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 492-016
 (4)  
Attach the sling cradle to the inboard elevator PCP (9) and bars to the elevator structure (Fig. 201).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(59)