(b)  
Apply an aft force at the control wheel center.

 1)  Make sure that the scale indication at the point where the elevators start to move is not more than 8.6 pounds.
 S 225-081
 (5)  
Do a check of the differential pressure switch:

 (a)  
Pressurize the AUX 1 and 2 pitot system to 2.5 - 3.5 psig (or 318 - 372 knots IAS).

 (b)  
Set the FLT CONTROL HYD POWER TAIL switches No. 1 and 4 on P461 the Pilots' Overhead Maintenance Panel to SHUTOFF.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 527 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  
Make sure that the ELEVATOR FEEL does not show on the EICAS status page.

 (d)  
Decrease the AUX 2 pitot pressure to the ambient pressure.

 (e)  
Make sure that the ELEVATOR FEEL is on the EICAS status page.

 (f)  
Decrease the AUX 1 pitot pressure to the ambient pressure.

 (g)  
Pressurize the AUX 2 pitot system to 2.5-3.5 psig (or 318-372 knots IAS).

 (h)  
Make sure that the ELEVATOR FEEL is on the EICAS status page.

 (i)  
Decrease the AUX 2 pitot static pressure to the ambient pressure.

 (j)  
Make sure that the ELEVATOR FEEL is not on the EICAS status page

 (k)  
Move the captain's control column at a constant rate from the full forward to the full aft to the full forward in approximately three seconds.

 (l)  
Make sure that the ELEVATOR FEEL does not show on the EICAS status page during the control column movement.

 (m)  
Set all the FLT CONTROL HYD POWER TAIL switches on the P461 Pilots' Overhead Maintenance Panel in NORM.

 S 225-113
 (6)  
Do a check of the elevator freeplay (inboard and outboard):

 (a)  
Make sure that the control column is in the neutral position.

 (b)  
Install a rigging pin E-2 at the aft quadrant.

 (c)  
Do a check of the inboard elevator freeplay:

 1)  Put the dial indicatior 1 inch from the trailing edge at the inboard end of the elevator.
 CAUTION: USE SUFFICIENT PADDING ON THE THE FORCE SCALE TO
_______ PREVENT DAMAGE TO THE ELEVATOR SURFACES.
 2)  Apply a down force of 30 pounds at about 11 inches from the the elevator trailing edge and at a point on the elevator rib opposite the pressurized PCA being tested (Fig. 506).
 NOTE: For padding, you can use a wood block of
____
 5 X 5 X 0.25 inch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 528 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

LOCATION TO APPLY FORCE
____THE LEFT ELEVATOR IS SHOWN;
NOTE: THE RIGHT SIDE IS OPPOSITE.
E99514
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 02 Page 529 ú Jun 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (d)

(e)

A
747-400 MAINTENANCE MANUAL
 3)  Set the dial indicator to zero while you apply the down force.
 4)  Slowly release the 30 pounds force.
 CAUTION: USE SUFFICIENT PADDING ON THE THE FORCE SCALE TO
_______ PREVENT DAMAGE TO THE ELEVATOR SURFACES.
 5)  Apply an up force of 90 +/- 5 pounds at about 11 inches from the the elevator trailing edge and at a point on the elevator rib opposite the pressurized PCA being tested.
 NOTE: For padding, you can use a wood block of
____
 5 X 5 X 0.25 inch.

 6)  Slowly release the 90 +/- 5 pounds force.
 7)  Make sure that the dial indicator reading is not greater than 0.21 inch.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(26)