S 865-111
(9)
Set the STAB TRIM 2 and 3 switches on the control stand to ON.
S 865-052
(10)
If the hydraulic power is not necessary, do this task: "Remove Hydraulic Power" (Ref 29-11-00/201).
S 865-053
(11)
If it is not necessary, do this task: "Remove the Pressure in the Pitot Static System" (Ref 34-11-00/201).
K.
Adjust the Input Rod to the Feel Computer
S 865-054
(1)
Use the STAB TRIM ALTN switches on the P8 control stand to set the stabilizer to 0.00 degrees stabilizer leading edge up. Set dimension "B" on the stabilizer jack screw to 7.42 +/- .03 inches. (AMM 27-41-00/201)
(a)
Make sure the stabilizer trim position indicators on the P8 control stand shows 3.00 units of trim.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 01 Page 521 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
ELECTRICAL CONNECTOR H2 HYDRAULIC RETURN LINES CHECKNUT
H3 HYDRAULIC FEEL PRESSURE LINES STABILIZER MAST
FEEL ELEVATOR COMPUTER ROD INPUT
RETURN SPRING H1 HYDRAULIC SUPPLY LINES
SEE C
TUBING PORT VENT P1 STATIC WASHER BOLT NUT
FWD P2 PITOT LINE (2 LOCATIONS) ARM INPUT SEE A
A
SEE B
BALLSCREW STOP MECHANISM TRIM DRIVE STABILIZER
DIMENSION "B" BALLNUT STOP
FWD
PIN E-5 RIG
B ARM INPUT
FWD C COMPUTER FEEL ELEVATOR
Elevator Feel Computer Adjustment
Figure 505
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-00
ALL ú ú 01 Page 522 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b) Make sure the B dimension on the stabilizer jackscrew is
7.42 +/- 0.05 inches.
S 235-055
(2)
Do a check of the feel computer adjustment:
(a)
Try to install the rig pin E-5 through the input arm into the feel computer. 1) If you cannot easily install the rig pin, adjust the input
rod.
S 835-056
(3)
Adjust the elevator feel computer input rod:
(a)
Set all the FLT CONTROL HYD POWER TAIL switches on the P461 Pilots' Overhead Maintenance Panel in SHUTOFF.
(b)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
1) P180 DC Power Distribution Panel a) 180E7 ELEV/RUD VLV SYS 2 b) 180E22 ELEV/RUD VLV SYS 4 c) 180H8 ELEV/RUD VLV SYS 1 d) 180H23 ELEV/RUD VLV SYS 3
(c)
Disconnect the input rod from the input arm of the feel computer.
(d)
Install the rig pin E-5.
(e)
Loosen the checknut on the adjustable end of the input rod.
(f)
Adjust the rod end until you can install the rod attachment bolt easily through the input arm and the rod end.
(g)
Install the bolt, washer and nut to connect the input rod to the input arm.
(h)
Tighten the nut.
(i)
Make sure the rod end extends a minimum of half of the distance across the safety hole in the rod.
(j)
Tighten the checknut on the rod end.
(k)
Remove the rig pin E-5.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 飛行操縱 FLIGHT CONTROLS 3(23)
