0.56 MAX RIG PIN
BRACKET SLOT
0.40 MAX
TRANSMITTER CLAMPING CRANK
D
SCREWS
____LEFT ELEVATOR POSITION TRANSMITTERS SHAFTNOTE:
SHOWN. RIGHT TRANSMITTERS SIMILAR E CLAMPING SCREW
Elevator Position Transmitter Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-38-01
ALL ú ú 01 Page 402 ú Oct 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(3) S 864-016Make sure the FLT CONTROL HYD POWER TAIL switches on the P461, Pilots' Overhead Maintenance Panel are in NORM.
(4) S 014-017Open the access door 312A.
S 864-018
WARNING: MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE STABILIZER AND
_______ THE ELEVATOR SURFACES BEFORE YOU MOVE THE STABILIZER. THE STABILIZER AND THE ELEVATOR SURFACES CAN MOVE QUICKLY AND CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(5)
Use the STAB TRIM ALTN switches on the control stand to set the stabilizer and the elevators to the neutral position.
S 864-019
(6)
Set the STAB TRIM 2 and 3 switches on the control stand to CUTOUT.
S 864-020
(7)
Set the FLT CONTROL HYD POWER TAIL switches on the P461, Pilots' Overhead Maintenance Panel to SHUTOFF.
(a)
Make sure the four VALVE CLOSED lights come on.
S 864-021
(8)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P7, Overhead Circuit Breaker Panel 1) 7E6, STAB TRIM L CONT 2) 7E7, STAB TRIM L S/O VALVE 3) 7E19, STAB TRIM R CONT 4) 7E20, STAB TRIM R S/O VALVE
(b)
P180, DC Power Distribution Panel 1) 180H8, ELEV/RUD VLV SYS 1 2) 180E7, ELEV/RUD VLV SYS 2 3) 180H23, ELEV/RUD VLV SYS 3 4) 180E22, ELEV/RUD VLV SYS 4
(c)
P6, Main Power Distribution Panel 1) 6J25, RUD/ELEV IND 2) 6J24, RUD/ELEV SENSOR
S 014-022
(9) Remove the third ceiling panel forward of the No. 1 doors to get access to the control column torque tube.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-38-01
ALL ú ú 02 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 494-023
(10)
Install the rig pin E-1 in the rig pin hole at the left side of the control column torque tube.
S 014-024
(11)
Open the access door 315A to get access to elevator aft quadrant.
S 494-025
(12)
Install the rig pin E-2 in the rig pin hole at the bottom of the elevator aft quadrant.
(a)
Install the rig pin into the hole with hand pressure only.
E.
Remove the Elevator Position Transmitter
S 014-004
(1)
Open these access panels for the applicable transmitter:
(a)
334KBL, LO Transmitter
(b)
334GBL, LI Transmitter
(c)
334GBR, RI Transmitter
(d)
334KBR, RO Transmitter
S 034-005
(2)
Disconnect these electrical connectors from the applicable
transmitter:
(a)
DT438, LO transmitter
(b)
DT1672, LI transmitter
(c)
DT1673, RI transmitter
(d)
DT437, RO transmitter
S 034-006
(3)
Disconnect the bonding jumper from the transmitter.
S 024-007
(4)
Remove the transmitter assembly:
(a)
Remove the nut, the washer, and the screw that attach the control rod to the crank.
(b)
Remove two screws, washers, and nuts that attach the bracket to the airplane structure.
(c)
Remove the transmitter, the bracket and the crank assembly from the airplane.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(112)
