S 715-011

 (4)  
Do this task: "Operational Test - Stabilizer Trim Elevator Control Actuated Limit Switches" (Ref paragraph 3.).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-07
 ALL  ú ú 01 Page 505 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 TASK 27-41-07-715-012
 3.  Operational Test - Stabilizer Trim Elevator Control Actuated Limit Switches___________________________________________________________________________
 A. General
 (1)  
This task is an operational test of the actuated limit switches. To do this test, you will operate the stabilizer trim control system. During the test, it is necessary to monitor the stabilizer trim indicators to examine the operation of the actuated limit switches.

 (2)  
All the actuated limit switches are on the same bracket. You must do the operational test for the actuated limit switches after the adjustment.

 B.
Special Tools and Equipment

 (1)  
4MIT65B80307-1 Control Column Protractor (Recommended)

 (2)  
F52485-500 Protractor (Alternative)

 C.
References

 (1)  
AMM 22-10-00/501, Autopilot/Flight Director System

 (2)  
AMM 24-22-00/201, Manual Control

 (3)  
AMM 29-11-00/201, Main Hydraulic Supply System

 D.
Access

 (1)  
Location Zone
 211 Passenger Cabin-Nose to First Door, LH

 E.
Procedure

 S 015-013
 (1)  
Open the third middle ceiling panel forward of the No. 1 door for access to elevator controls.

 S 495-014

 (2)  
Install the rig pin E-1 at the elevator forward quadrant.

 S 225-015

 (3)  
Measure the control column angle at the neutral position:

 (a)  
Attach the protractor against the front or the rear of the control column.

 (b)  
Put the protractor bubble in the center.

 (c)  
Measure the control column angle.

 (4)
Remove the rig pin E-1 from the elevator forward quadrant.

 (5)
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).

 S 095-018
 S 865-019
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-07
 ALL  ú ú 01 Page 506 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 865-020
 WARNING:_______ MOVE ALL PERSONS AND EQUIPMENT AWAY FROM THE ELEVATORS BEFORE
 YOU PRESSURIZE THE HYDRAULIC SYSTEMS.  THE ELEVATORS CAN MOVE
 QUICKLY TO THE NEUTRAL AND CAUSE INJURY TO PERSONS OR DAMAGE TO

 EQUIPMENT.
 (6)  
Do this task to pressurize the hydraulic systems No. 2 and 3: "Supply Hydraulic Power" (AMM 29-11-00/201).

 S 865-021

 (7)  
Set the stabilizer at about mid travel.

 S 715-022

 (8)  
Do a test of the actuated limit switch:

 (a)  
Hold the STAB TRIM switches on the control wheel to NOSE DN.

 1)  While the stabilizers move, pull the control column aft carefully until the actuated limit switch stops the stabilizer travel.
 2) Hold the control column in this position. 3) Make sure that the stabilizer trim indicators on the control stand do not show 0.80 units of trim.
 (b)  
Do these steps to measure the control column displacement from the neutral position: 1) Put the protractor bubble in the center 2) Measure the control column angle at this position. 3) Make sure the difference between the control column angles

 at the neutral and aft positions is 3.7-5.5 degrees.

 (c)  
Hold the STAB TRIM switches on the control wheel to NOSE UP.

 1)  While the stabilizers move, push the control column forward carefully until the actuated limit switch stops the stabilizer travel.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(185)