(c)  
Make sure that the trailing edge of the inboard and outboard elevators is aligned in the tolerance of 2.2-2.8 inches.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 525 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (d)  Make sure these ELEVATORS surface positions show on the EICAS flight controls maintenance page: 1) 1.0 +/-0.2 degrees up for the inboard elevators. 2) 1.0 +/-0.5 degrees down for the outboard elevators.
 S 225-078
 (2)  
Do a check on the control column neutral position and travel:

 (a)  
Install the rig pin E-2 at the bottom of the aft quadrant.

 (b)  
Use the adjustable protractor to find the angle of the floor: 1) Set the protractor parallel to the airplane centerline. 2) Find the angle of the floor in the flat location adjacent

 to the control columns.

 (c)  
Attach the protractor to the forward or aft face of the captain's control column with a clamp.

 (d)  
Set the control column in the neutral detent.

 (e)  
Make sure that the control column angle is 7.28-9.28 degrees forward of the line normal to the floor.

 (f)  
Make sure that the COLUMN position on the EICAS flight controls maintenance page is 0 | 1.0 degree.

 (g)  
Decrease the AUX 1 and 2 pitot system pressure to ambient.

 (h)  
Remove the rig pin E-2.

 (i)  
Move the control columns forward to stop and hold. 1) Make sure that the control column angle is 11.5-13.5 degrees forward from the neutral position.

 2)  Make sure that the COLUMN position on the EICAS flight controls maintenance page is 12.5 | 1.0 degrees down.

 (j)  
Move the control columns aft to stop and hold. 1) Make sure that the control column angle is 11.67-13.67 degrees aft of the control column neutral position.

 2)  Make sure that the COLUMN position on the EICAS flight controls maintenance page is 12.67 | 1.0 degrees up.
 S 225-079
 (3)  
Do a check on the elevator travel (inboard and outboard).

 (a)  
Move the control columns forward to stop and hold.

 1)  Make sure that the inboard elevator travel is 28.29-29.30 inches.
 NOTE: The inboard elevator travel is measured diagonally
____ between the trailing edge tip and the body index plate.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-00
 ALL  ú ú 01 Page 526 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2)  Make sure that the trailing edge of the inboard and outboard elevators is aligned in the tolerance of 1.94-2.98 inches.
 3)  Make sure that the two elevator position pointers on the surface position display of the EICAS status page are at the lower index mark (elevator full down).
 4)  Make sure these ELEVATORS surface positions show on the EICAS flight controls maintenance page. a) 14.6-15.4 degrees down for inboard elevators. b) 16.1-17.6 degrees down for outboard elevators.
 (b)  Move the control column aft to stop and hold. 1) Make sure that the inboard elevator travel is 42.75-43.77 inches.
 2)  Make sure that the trailing edge of the inboard and outboard elevators is aligned in the tolerance of 2.29-3.30 inches.
 3)  Make sure the two elevator position pointers on the surface position display of the EICAS status page are at the upper index mark (elevator full up).
 4)  Make sure these ELEVATORS surface positions show on the EICAS flight controls maintenance page. a) 24.8-25.8 degrees up for the inboard elevator. b) 22.1-23.7 degrees up for the outboard elevator.
 (c)  Put the control columns to neutral.
 S 225-080
 (4)  
Do a check on the breakout forces of the control column with the spring scale:

 (a)  
Apply a forward force at the control wheel center.

 1)  Make sure that the scale indication at the point where the elevators start to move is not more than 6.6 pounds.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(25)