EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-02
ALL ú ú 02 Page 222 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
HORIZONTAL STABILIZER HINGE - INSPECTION/CHECK
______________________________________________
1. General_______
A. This subject has three tasks. The first task is an inspection of the hinge pin for dimensional tolerance. The second task is an inspection of the hinge pin for corrosion. The third task is a free play check of the horizontal stabilizer.
B. In the first task you measure the inner or outer diameter of the parts of the hinge pin. The parts include bearings and outer pin.
C. In the second task you examine the stabilizer pivot pin for corrosion.
D. In the third task you examine the stabilizer flutter free play limit.
TASK 27-41-02-206-001
2. Horizontal Stabilizer Hinge Wear Limits Inspection__________________________________________________
A. Standard Tools and Equipment
(1)
Micrometer 2.0-2.5 inches (50-64 millimeters).
(2)
Vernier Caliper or Micrometer
B.
References
(1)
AMM 27-41-02/201, Stabilizer Hinge
C.
Access
(1)
Location Zone
315-316 Area Aft of Stabilizer Box
(2)
Access Panel
315A Access Door
D.
Procedure
(1)
Do this task: "Stabilizer Hinge Removal" (AMM 27-41-02/201).
S 226-003
(2)
Examine the parts for worn areas:
(a)
Use a micrometer or a vernier caliper to measure the parts.
(b)
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.
S 026-002
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-02
ALL ú ú 01 Page 601 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SEE B
STA 2598 BULKHEAD
HORIZONTAL STABILIZER CENTER SECTION FREE PLAY
CHECK TOOL
SEE A HYDRAULIC LINE TO HAND PUMP SHEAR DECK
STABILIZER FITTING
HINGE (4 LOCATIONS)HINGEFITTING SUPPORT STA 2598FITTING BULKHEAD
HINGE TRUSS
BEARING
OUTER PIVOT PIN
HORIZONTAL STABILIZER HINGE BEARING
SEE C
FREE PLAY CHECK TOOLS USAGE A
90-DEGREE QUADRANT
1. BEARING/ OUTER PIN TRUSS
FWD INBD
RIGHT HINGE ASSEMBLY (LEFT HINGE ASSEMBLY IS OPPOSITE) PIN CROSS-SECTION
B C
DESIGN LIMITS WEAR LIMITS
MAXPER-DIAMETER
INDEX NO. PART NAME DIM. MIN MAX MITTED WEAR DIM. ANCE CLEAR-DIA PART REPLACE WORN PART REPAIR WORN INSTR REPAIR
INCH INCH INCH INCH
(mm) (mm) (mm) (mm)
2.3745 2.3765 2.3788
BEARING ID (60.312) (60.363) (60.422) 0.0050 X
1 2.3736 2.3758 2.3695 (0.127)
OUTER PIN OD (60.289) (60.345) (60.185) X 1
TABLE I
1
YOU CAN REPAIR THE WORN PART, REFER TO THE OVERHAUL MANUAL FOR REPAIR PROCEDURE.
Horizontal Stabilizer Wear Limits Figure 601
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-41-02
ALL ú ú 01 Page 602 ú Feb 18/00
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(152)
