E.
Procedure to Measure the Torsional Free Play

 S 866-007
 (1)  
With the help of a spring scale, apply a clockwise pull of 30 pounds on the 2 X 4 at 100-inch arm from the shock strut centerline.

 (a)  
Set the dial indicator gage to "0".

 (b)  
Loosen the load.

 S 866-008
 (2)  
Apply a counterclockwise pull on the 2 X 4 as in step (1).

 (a)  
Write the value on the dial indicator.

 (b)  
Loosen the load.

 S 976-009
 (3)  
Do the steps (1) and (2) for a total of 5 cycles.

 S 976-011

 (4)  
Find the average value of torsional free play.

 S 976-012

 (5)
Make sure the average value you will get in step (5) is less than

 0.14 inch.
 S 226-013
 (6)  
If the average value is more than maximum permitted, examine the parts or assemblies given below for allowable wear limits and replace the applicable parts:

 (a)  
The torsion links (AMM 32-11-51/601)

 (b)  
The shock strut inner and the outer cylinder of the torsion link attachment lugs (AMM 32-11-51/601).

 (c)  
The trunnion link to outer cylinder clevis joint (AMM 32-11-11/601).

 (d)  
The forward trunnion bearing (AMM 32-11-83/601)

 (e)  
The aft trunnion bearing

 S 226-014
 (7) If you replace one of the parts, do steps (1) to (6) again to make sure that the torsional free play is in the approved limits.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-00
 ALL  ú ú 03 Page 605 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 F. Put the Airplane in Its Usual Condition
 S 086-015
 (1)  
Remove the 12-inch C-clamp from the shimmy damper.

 S 866-036

 (2)  
Lower the axle jack and remove it from the airplane (AMM 07-11-31/201).

 S 616-016

 (3)  
Fill the shock strut with air to 250-psi extend pressure before you lower the airplane.

 S 866-017

 (4)  
Lower the airplane off of the jacks (AMM 07-11-11/201).

 (a)  
Remove the jacks from the airplane.

 S 616-018
 (5)  Service the shock strut (AMM 12-15-31/301).
 TASK 32-11-00-206-053
 4. Main Landing Gear Torsion Links Apex Joint Inspection
______________________________________________________
 A. General
________
 (1)  The apex joint inspection is important to make sure the shimmy damper functions properly and the apex thrust washers or apex bushings are not worn such that the shimmy damper effectiveness is reduced.
 NOTE: It is important that you adjust the shimmy damper correctly
____ and tighten the apex nut of the torsion link to specified torque before you do this inspection.
 B. References
 (1)  
AMM 32-00-01/201, Ground Lock Assemblies

 (2)  
AMM 32-11-51/401, Main Landing Gear Torsion Links

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-00
 ALL  ú ú 02 Page 606 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (3)  
AMM 32-11-51/601, Main Landing Gear Torsion Links

 (4)  
AMM 32-11-81/501, Main Landing Gear Damper

 C.  
Access

 (1)  
Location Zone
 216 Left Main Wheel Well
 217 Right Main Wheel Well

 D.  
Prepare for the Inspection

 S 496-054
 (1)  
Make sure that the ground lock assemblies are installed in the nose and main landing gear (AMM 32-00-01/201).

 E.  
Procedure to Inspect the Apex Joint

 S 226-049
 (1)  
Examine the clearance between the apex thrust washer and the apex nut.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(57)