(h)
Install the lockbolt, the washer, the nut in the apex nut and the lockwasher.
(i)
Tighten the checknut 50 to 100 pound-inches.
(j)
Install the lockwire from the lockbolt to the checknut.
S 865-023
(3)
Put the Airplane Back to its Usual Condition.
(a)
Lower the axle jack and remove it from the airplane (AMM 07-11-31/201).
TASK 32-11-81-705-014
3. Main Gear Damper Test_____________________
A. Access
(1)
Location Zone
235 Left Main Wheel Well
236 Right Main Wheel Well
B.
Test Main Gear Damper
S 215-015
(1)
Do a visual check on the unit for leakage at the bleeder plugs, the filler valve, the hydraulic line connection, and the piston rod seals.
(2)
Make sure the gear is adjusted as in step 2.C.(2).
(3)
Push the thrust washer against the lower torsion link.
(4)
Measure the distance between the thrust washer and the apex nut.
S 225-019
(5)
If the distance is not more than .005 inch maximum, no more adjustment is needed,
S 725-016
S 435-017
S 225-018
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 503 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 225-020
(6)
If the distance is more than .005 inch, do a check on the apex thrust washers and the lower torsion link bushings for wear.
(a)
Adjust the gear as in step 2.C.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 504 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
MAIN LANDING GEAR DAMPER - INSPECTION/CHECK
___________________________________________
1. General
_______
A. This procedure only has illustration and a wear limits table which shows the data for wear limits. There are no procedures for the access, the removal, or the installation of the parts. Refer to the Main Landing Gear Damper - Removal/Installation for procedures to do these tasks.
TASK 32-11-81-206-001
2. Wear Limits for the Damper of the Main Landing Gear (Fig. 601)
___________________________________________________
A. Wear Limits for the Damper
S 226-002
(1) Refer to Fig. 601 for the inspection points and the wear limits table.
B
B
A
A
LOWER
MAIN
TORSION
GEAR
LINK
DAMPER
Main Landing Gear Damper Wear Limits
Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 601 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
B-B
Main Landing Gear Damper Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 602 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
INDEX NO. PART NAME DIM. DESIGN LIMITS WEAR LIMITS REPLACE PART WORN REPAIR WORN PART REPAIR INSTR.
DIAMETER MAX WEARDIM. MAX DIAM CLEAR-ANCE
MIN MAX
1 HOUSING 2 ID 2.620 2.622 2.626 0.009 X
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(109)
