32-13-11
 ALL  ú ú 01 Page 403 ú Oct 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE  G 
STRIPE INDEX  BAC 701 BLACK BMS 10-60, TYPE I 
INBD  FWD
4.0 INCHES  CLAMPS (REF) DOOR SUPPORT SHOCK STRUT 
1.0 INCH  |0.025 INCHES 2.5 TRUE 
FWD 
G 
Figure 401 (Sheet 3) Main Gear Shock Strut Door Installation RIGHT MAIN LANDING GEAR ASSEMBLY OPPOSITE) (LEFT MAIN LANDING GEAR ASSEMBLY SHOWN, MAIN LANDING GEAR DOOR INDEX STRIPE 

B02322
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 404 ú Nov 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (b)  Remove the nuts, washers and bolts to disconnect the lower shock strut door support (8) from the clamp (9).
 S 034-005
 (5)  Remove the door assembly from the airplane.
 TASK 32-13-11-424-055
 3.  Shock Strut Door Assembly Installation (Fig. 401)______________________________________
 A. References
 (1)  
AMM 07-11-11/201, Airplane Jacking

 (2)  
AMM 32-00-01/201, Ground Lock Assemblies

 B.
Equipment

 (1)  
Hydraulic test bench that can supply 20 gpm at 3000 psi

 (2)  
7355 Mylar Tape, Mystic Tape, Division of Borden Chemical Co., 60 Happ Road, Northfield, Illinois 60093 (Preferred).

 Y8412 Mylar Tape, 3M Company, Industrial Tape Division, 3M Center, St. Paul, Minnesota 55101. (Optional)
 C. Access
 (1)  
Location Zones
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 D.
Shock Strut Door Assembly Installation

 S 424-006
 (1)  
Put the door in its position on the shock strut of the landing gear.

 S 424-008

 (2)  
Install the bolts, washers and nuts to connect the upper (3) and the lower (5) door supports for the drag strut to the clamps (1 and 4).

 S 424-051

 (3)  
Install the bolts, washers and nuts to connect the upper (10) door support for the drag strut to the clamp (11).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 405 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (4)  S 424-052Tighten the nuts to 10-20 pound-inches (1.13-2.26 newton-meters).
 (5)  S 424-053Install the cotter pins. If it is necessary, loosen the nuts to the nearest castellation to align the holes for the pins.
 (6)  S 424-054Install the bolts, washers and nuts to connect the lower (8) door support for the drag strut to the clamp (9).
 (7)  S 034-009Disconnect the control rod for the outboard wing door.
 (8)  S 734-010Lift the airplane until all tires are clear of the ground (AMM 07-11-11/201).
 (9)  S 764-011Examine that electrical power is available.
 S 484-012

 (10)
 Connect the external hydraulic test bench.

 (a)
Do not pressurize the hydraulic system A. S 034-013

 (11)
 Remove the ground lock assemblies on the repaired landing gear (AMM 32-00-01/201).

 S 844-014

 (12)
 Set the control lever for the landing gear in the UP position.

 S 724-015 CAUTION: MAKE SURE THAT THE STRUT DOORS ARE CLEAR OF THE WING PANELS
_______ BEFORE YOU FULLY RETRACT THE GEAR. THE STRUT DOORS CAN CAUSE DAMAGE TO THE WING PANELS IF THE DOOR ARE NOT CLEAR.
 (13) Operate the test bench to slowly retract the gear.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-13-11
 ALL  ú ú 01 Page 406 ú Nov 12/01
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2