WARNING: MAKE SURE THAT YOU DEFLATE THE SHOCK STRUT FULLY BEFORE YOU
_______ LOOSEN THE VALVE BODY. THE AIR PRESSURE CAN BLOWOUT THE VALVE BODY WHICH CAN CAUSE INJURY TO PERSONS.
MAKE SURE THAT NO PERSON OR EQUIPMENT ARE BELOW THE AIRPLANE WHILE THE AIRPLANE DESCENDS.
(8)
Compress the shock strut (Fig. 401).
(a)
Remove the dust cap from the air charging valve at the top of the shock strut (Fig. 401).
(b)
Loosen the release nut to one or two turns.
NOTE: You will immediately see bubbles in the fluid in the
____ shock strut when you release the pressure. Deflate the shock strut slowly to prevent the leakage of th fluid through the air valve.
(c)
Deflate and compress the shock strut.
(d)
Install the oleo lock assembly on the main landing gear to keep the shock strut compressed.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-00
ALL ú ú 01 Page 403 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 584-073
(9) Lift the airplane on jacks until the tires have sufficient contact with the ground to prevent rotation of the wheels (AMM 07-11-11/201).
NOTE: Approximately 4 inches is necessary to lift the airplane on
____ jacks.
S 934-074
(10)
Make a mark on the ground around the tire contact area.
S 034-017
(11)
Remove the hydraulic lines from the drag strut (Fig. 402).
(a)
Disconnect the hydraulic lines from the top side of the trunnion link on the hydraulic swivel (11) and drain the lines in a container.
(b)
Disconnect the hydraulic lines from their connections on the wheel well ceiling and drain the lines in a container.
(c)
Remove the hydraulic swivel (11) from the trunnion link.
(d)
Remove the door actuator fitting (13).
(e)
Loosen all the clamps (8) which hold the hydraulic lines (7) to the drag strut.
SEE A
RELEASE
NUT DUST
AIR CAP
CHARGING
VALVE
SHOCK
STRUT
INBD
FWD
A
Shock Strut Air Charging Valve
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-00
ALL ú ú 01 Page 404 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(f)
Disconnect the hydraulic lines from the bracket (3) on the lower drag strut and drain the lines in a container.
(g)
Disconnect the hydraulic line connection (6) from the main gear damper (5) and drain the lines in a container.
(h)
Remove all the hydraulic lines from the drag strut.
(i)
Seal all the hydraulic lines and connections with caps.
S 034-018
(12)
Remove the electrical harness (Fig. 402).
(a)
Disconnect the electrical harness (9) near the top of the trunnion link (10).
(b)
Loosen the clamps (8) for the electrical harness (9) on the upper drag strut.
(c)
Wind the harness into a coil. 1) Attach the harness to the lower drag strut with tape.
S 024-178
(13)
If you do landing gear procedures that do not affect the actuator assembly (12), disconnect the actuator from the actuator walking beam arm and the trunnion pin (AMM 32-32-11/401).
(a)
Put the actuator assembly out of the way of the landing gear.
S 024-019
(14) If you do landing gear procedures that do affect the actuator assembly (12), remove the actuator assembly (AMM 32-32-11/401).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(44)
