(d)  
Put the bearing assembly in the holding fixture.

 (e)  
Remove the bearing from the bearing housing with spanner wrench.

 S 024-013
 (3)  
For threaded bearing assembly with cotter pin, do the following steps:

 (a)  
Remove the cotter pin and the pin from the bearing assembly.

 (b)  
Remove the bearing from the bearing housing.

 NOTE: If the removal of the bearing is difficult, put the
____ bearing assembly in the holding fixture and remove it with spanner wrench .
 S 034-004
 (4)
For shrink fit bearing assembly, do the following steps:

 (a)  
Remove the rivets that lock the ring nut to the bearing housing.

 (b)  
Put the bearing assembly in the holding fixture.

 (c)  
Remove the ring nut with spanner wrench and discard it.

 (d)  
Remove the bearing from the bearing housing with a mandrel.

 S 214-005
 (5)
Do a check on the bearing housing for damage or distortion.

 S 164-006

 (6)  
If the bearing housing is not damaged, clean and remove the grease from the bearing housing.

 TASK 32-11-83-404-007
 3. Main Landing Gear Forward Trunnion Bearing Installation (Fig. 401)
_______________________________________________________
 A. Special Tools and Equipment
 (1)  
Mandrel, Forward Trunnion Bearing, Main Landing Gear - C32007-1 Use to install the shrink fit bearing in the bearing housing.

 (2)  
Holding Fixture Assembly, Forward Trunnion Bearing Housing , Main Landing Gear - F80096-4

 (3)  
Holding Fixture Assembly, Forward Trunnion Bearing Housing , Main Landing Gear - F80096-7

 (4)  
Spanner Wrench, Forward Trunnion Bearing - F80018-1 Use to install the bearing and the bearing nut.

 (5)  
Spanner Wrench, Forward Trunnion Bearing - F80018-2 Use to install the bearing and the bearing nut.

 B.
Standard Tools and Equipment

 (1)  
Container - For handling liquid nitrogen

 (2)  
Wooden Dowel

 C.
Consumable Materials

 (1)  
C00528 Compound - Corrosion Preventive MIL-C-16173, Grade 2 or MIL-C-11796, Class 3

 (2)  
Sealant - BMS 5-95 (AMM 20-30-11)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-83
 ALL  ú ú 01 Page 403 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 D.
E.
F.
A
737-300/400/500MAINTENANCE MANUAL
 (3)  
D00633 Grease - BMS 3-33

 (4)
D00164 Grease - MIL-G-23827References

 (1)  
AMM 32-11-11/401, Main Landing Gear Trunnion Link

 (2)
OHM 32-16-31, Forward Trunnion Bearing AssemblyAccess

 (1)  
Location Zone 310 Left Main Landing Gear 410 Right Main Landing Gear

Procedure
 S 624-008
 (1)  
Apply a layer of corrosion preventive compound to the inside diameter of the bearing housing.

 S 424-009

 (2)  
For threaded bearing assembly with rivets, install the bearing (OHM 32-16-31).

 S 424-014

 (3)  
For threaded bearing assembly with cotter pin, do the following steps:

 (a)  
Apply grease to the threads of the bearing housing and the bearing.

 (b)  
Turn the bearing into the bearing housing until it is down against the step on the housing.

 (c)  
Turn the bearing back to a minimum amount to align the slots.

 (d)  
Put a wooden dowel in the aligned slots to keep them aligned.

 (e)  
Drill a 0.1845 - 0.1855 hole in the bearing with the hole in the housing as a pilot.

 (f)  
Apply BMS 5-95 sealant to the shank of the pin.

 (g)  
Press fit the pin through the hole.

 (h)  
Remove the unwanted sealant but let sealant stay to make a fillet seal around the pin head.

 (i)  
Install the cotter pin.

 S 424-010
 (4)  
For shrink fit bearing assembly, do the following steps:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(111)