32-09-20
 ALL  ú ú 02 Page 421 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (e)  
Set the test switch on the left ADC to the normal position.

 (f)  
Move the flap lever to the 30 unit position. 1) Make sure the flaps retract to the 30 unit position.

 (g)  
Set the test switch for the flap load limiter to the SYSTEM TEST position and hold it in this position. 1) Make sure the test light comes on. 2) Make sure the flaps do not retract.

 (h)  
Press the ground sensing and air sensing test switches on the E11 module at the same time to put the airplane in the AIR mode. 1) Make sure the test light goes off

 S 844-077
 (3)  
Put the airplane in its initial condition.

 (a)  
Put the airplane in the ground mode.

 (b)  
Move the flap lever to the UP position.

 (c)  
Remove pressure from hydraulic system A and B, if it is not necessary (AMM 29-15-00/201).

 (d)  
Remove electrical power, if it is not necessary (AMM 24-22-00/201).

 TASK 32-09-20-724-089
 5.  Landing Gear Logic Shelf - Latching Relay - Test________________________________________________
 A. Special Tools and Equipment
 (1)  
Deactuator bars for the proximity sensors:

 (a)  
Material: 5052, 6061, 7075, or 2024 aluminum or sheet copper

 (b)  
Size: For rectangular sensors - 1.5 x 0.75 x 0.05 inches thick For round sensors - 1.0 x 1.0 x 0.05 inches thick

 B.
References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 32-00-01/201, Ground Lock Assemblies

 C.
Access

 (1)  
Location Zones
 102 Control Cabin
 203 Nose Gear Wheel Well
 204 Nose Gear

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-09-20
 ALL  ú ú 02 Page 422 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 D.  Test for the R374 Nose Gear Latching Relay.
 S 844-081
 (1)  
Prepare for the test:

 (a)  
Make sure the ground locks are installed on all the gear (AMM 32-00-01/201).

 (b)  
Supply electrical power (AMM 24-22-00/201).

 (c)  
Make sure these circuit breakers are closed on the P6 panel: 1) LANDING GEAR AIR/GND RELAY & LGT 2) AURAL WARNING

 (d)  
Do these steps to prevent the sound of the takeoff warning: 1) Make sure the stabilizer arrow on the middle console is in

 the green band. 2) Move the flap lever to the 15 unit position. 3) Make sure the speed brake lever is in the down position.
 S 724-082
 (2)  
Do a test of relay R374:

 (a)  
Move the throttles to the fully forward position.

 (b)  
Move the landing gear lever to the DN position.

 1)  Make sure the green light for the nose gear (on the P2 Panel) is on and the red light is off.

 (c)  
Move the landing gear lever to the OFF position.

 1)  Make sure the red light for the nose gear comes on and green light stays on.

 (d)  
Put deactuator bars on nose gear lock sensor S846, and on nose gear down sensor S845.

 (e)  
Remove the deactuator bar from the nose gear lock sensor S846.

 (f)  
Make sure the red light for the nose gear goes off.

 (g)  
Move one of the two throttles to the idle position. 1) Make sure the red light for the nose gear comes on. 2) Make sure you hear the aural warning continuously.

 (h)  
Remove the deactuator bar from sensor S845.

 S 844-083
 (3)  
Put the airplane in its initial condition.

 (a)  
Move the two throttles to the idle position.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-09-20
 ALL  ú ú 02 Page 423 ú Jul 12/99
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(39)