32-11-83
 ALL  ú ú 02 Page 601 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (b)  Do a check on the condition of the bearing assembly as follows:
 1)  A minimum of five rivets must be installed with no signs of damage (deformed, cracked heads, sheared) and up to three rivets are permitted to be gone.
 2)  A minimum of four rivets must be installed with no signs of damage (deformed, cracked heads, sheared) and up to four rivet heads are permitted to be gone.
 3)  A minimum of three rivets must be installed with no signs of damage (deformed, cracked heads, sheared) and up to five rivet heads can show signs of damage, with up to two of the five rivets or rivet heads are permitted to be gone.
 (c)  
If the bearing assembly is in one of the above conditions, rework or replace the bearing assembly at the first maintenance opportunity but not more than 2000 flight cycles (OHM 32-16-31).

 (d)  
If the condition of the bearing assembly is less than the outlined above, do the inspection again at 920 flight cycle intervals. 1) Continue this inspection interval until you replace or

 rework the bearing assembly.

 (e)  
If all the rivets are installed, do the inspection again at subsequent 4600 flight cycle intervals.

 S 226-012
 (2)  
Do the steps that follows if it is necessary to examine the clearance of the forward trunnion bearing.

 S 226-004

 (3)  
Examine the vertical clearance of the forward trunnion bearing for the main landing gear.

 (a)  
Attach the dial indicator to the rear spar structure near the forward trunnion bearing to measure the vertical clearance.

 (b)  
Apply the force at the wheel to push the landing gear forward as far as it will go.

 (c)  
Set the dial indicator with the trunnion as near as possible to the forward trunnion bearing.

 (d)  
Adjust the dial indicator to read zero.

 (e)  
Push and pull at the wheel to move the landing gear forward and aft.

 (f)  
Read the bearing clearance on the dial indicator.

 (g)  
If the clearance is larger than 0.030 inch for shrink fit bearing assemblies, or 0.050 inch for threaded bearing assemblies, examine the worn part limits (see Fig. 601).

 (h)  
Replace the parts if it is necessary.

 S 226-005
 (4)  
Examine the horizontal clearance of the forward trunnion bearing for the main landing gear.

 (a)  
Attach the dial indicator to the rear spar structure near the forward trunnion bearing to measure the horizontal clearance.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-83
 ALL  ú ú 03 Page 602 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
FWD INBD REAR SPAR
2
1
3
2 4 3
FWD INBD
RING NUT
2 5
3
3
A
Main Landing Gear Forward Trunnion Bearing Assembly Wear Limits Figure 601 (Sheet 1)
E82312
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-83
 ALL  ú ú 01 Page 603 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
INDEX NO.  PART NAME 6  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE PART WORN  REPAIR WORN PART  REPAIR INSTR. 
DIAMETER  MAX WEAR DIM.  DIA CLEAR-ANCE MAX 
MIN  MAX 
1  BEARING SUPPORT  ID  4.757  4.758  4.761  0.011  X  1 
2  BEARING HOUSING  OD  4.749  4.750  4.746  8  X  1 
3  BEARING  4.125  0.015 2  X 

INDEX NO.  PART NAME 7  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE PART WORN  REPAIR WORN PART  REPAIR INSTR. 
DIAMETER  MAX WEAR DIM.  DIA CLEAR-ANCE MAX 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(113)