B.
Special Tools and Equipment

 (1)  
Actuator bars for the proximity sensors:

 (a)  
Material: 1020 steel per MIL-S-7952, 15-5PH steel, 17-4PH steel per AMS 5643, Permalloy - HYMU (carpenter steel) or Molly Permalloy (Allegheny Ludlum).

 (b)  
Size: For rectangular sensors - 1.5 x 0.75 x 0.05 inches. For round sensors - 1.0 x 1.0 x 0.05 inches.

 (2)  
Deactuator bars for the proximity sensors:

 (a)  
Material: 5052, 6061, 7075, or 2024 aluminum or sheet copper

 (b)  
Size: For rectangular sensors - 1.5 x 0.75 x 0.05 inches. For round sensors - 1.0 x 1.0 x 0.05 inches.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-09-20
 ALL  ú ú 01 Page 407 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
 (3)  
The equipment that follows is necessary only when you do a test of the Engine Speed Detector Card, M1190:

 (a)  
Function generator which can produce a 5 volt square or sine wave, adjustable from 50 Hz to 3000 Hz. Wavetek Model 171 Synthesizer/Function Generator - Wavetek Pacific Measurements, Inc., 488 Tasman Dr., Sunnyvale, CA 94089.

 (b)
Tachometer System Test Box - C77002References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 29-15-00/201, Hydraulic Systems A, B, and Standby

 (3)  
AMM 32-00-01/201, Ground Lock Assemblies

 (4)  
AMM 71-11-02/201, Fan Cowl Panels

 (Used in the test of card M1190)Access

 (1)  
Location Zones 102 Control Cabin 203 Nose Gear Wheel Well 204 Nose Gear 205 Electronic Compartment 215 Left Main Gear Wheel Well 217 Right Main Gear Wheel Well 310 Left Main Gear 410 Right Main Gear 502 No. 1 Engine Fan Cowl

Test for the M981 Circuit Card (Right Main Gear Downlock Switch)
______________________________
 S 844-019
 (1)  
Prepare to do the test:

 (a)  
Make sure the ground locks are installed on all the gear (AMM 32-00-01/201).

 (b)  
Supply electrical power (AMM 24-22-00/201).

 (c)  
Make sure this circuit breaker is closed on the P6 panel: 1) LANDING GEAR AIR/GND RELAY & LTG

 (d)  
Make sure the landing gear lever is in the DN position.

 S 724-019
 (2)  
Do the test of the M981 circuit card:

 (a)  
Make sure all green lights for the landing gear, on the P2 panel, are on.

 (b)  
Put a deactuator bar on the face of sensor S73 (downlock sensor for the right main gear).

 NOTE: Sensor S73 is on the side strut for the right main gear.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-09-20
 ALL  ú ú 02 Page 408 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 1)  Make sure the green light for the right main gear (on the P2 panel) goes off.
 (c)  Remove the deactuator bar from the sensor S73.
 1)  Make sure the green light for the right main gear (on the P2 panel) comes on.
 S 844-020
 (3)  
Put the airplane in its initial condition.

 (a)  
Remove electrical power, if it is not necessary (AMM 24-22-00/201).

 F.  Test for the M982 Circuit Card (Right Main Gear Uplock Switch)______________________________
 S 844-091
 (1)  
Prepare to do the test:

 (a)  
Make sure the ground locks are installed on all the gear (AMM 32-00-01/201).

 (b)  
Make sure there is no pressure in hydraulic systems A and B (AMM 29-15-00/201).

 (c)  
Supply electrical power (AMM 24-22-00/201).

 (d)  
Make sure this circuit breaker is closed on the P6 panel: 1) LANDING GEAR AIR/GND RELAY & LTG

 (e)  
Make sure the landing gear lever is in the DN position.

 S 724-025
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 1(31)