(a)  
Remove the shield.

 S 034-059
 (2)  
Remove the antiskid transducer to get access to the connectors (Ref 32-42-11/401).

 S 034-054

 (3)  
Pull the electrical connectors out of the axle and disconnect wires.

 S 024-061

 (4)  
Remove the hose clamps.

 NOTE: Do not remove the ratchet clamps and the tape from the hose
____
 unless replacement is necessary.

 S 024-062
 (5)  
Remove the hose assembly.

 S 014-055

 (6)  
Remove the front cover of the J-box assembly.

 (7)  
Remove the fittings from the J-box assembly.

 S 034-064

 (8)  
Remove the nuts and washers that attach the J-box assembly to the clamps.

 (9)  
Remove the J-box assembly from the axle.

 S 034-063
 S 024-065
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-87
 ALL  ú ú 01 Page 406 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 TASK 32-11-87-404-009
 4.  AIRPLANES WITHOUT BRAKE TEMPERATURE MONITORING WIRING; Main Landing Gear Electrical Harness Installation (Fig. 401)
_________________________________________________
 A.  Access
 (1)  
Location Zone
 310 Left Main Landing Gear
 410 Right Main Landing Gear

 B.  
Procedure

 S 434-010
 (1)  Put the hose assembly on the main gear and attach it to the gear with the clamps.
 NOTE: Make sure that the markers on the hose (V-1 thru V-4) are
____ installed correctly in relation to the clamp.
 S 844-024
 (2)
If the tape needs to be replaced, do the steps that follow:

 (a)  
Wind two layers of new tape around the hose (refer to BAC5801) and to the dimensions shown.

 NOTE: Have the layers of tape make an overlap of approximately
____ 0.25 inch.
 (b)  
Safety the ends of the taped areas with the ratchet clamps.

 (c)  
Keep the ratchet part of the clamp turned away from the gear structure to prevent galling.

 S 434-025
 (3)
Install the washer or washers (4) on the expandable fitting (3).

 S 424-026

 (4)
Put the expandable fitting in the hole of the main gear axle.

 S 424-027

 (5)  
Hold the expandable fitting (3), install the fitting (1) into the expandable fitting and tighten.

 S 214-028

 (6)  
Make sure that the expandable fitting has a tight fit in the main gear axle hole.

 (7)  
If it is still loose, add the washers.

 S 424-030

 (8)  
Feed the winded ends of the hose assembly through the fittings (1 and 2) and through the expandable fitting (3) into the hole of the axle.

 S 434-029
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-11-87
 ALL  ú ú 01 Page 407 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 424-031
 (9)  Pull the winded ends out of the axle ends and crimp on the connector.
 NOTE: If it is necessary, use the axle sleeves to make the clamp
____
 have a tight fit.

 S 424-032
 (10)
 Install the elbow of the hose assembly on the fitting (1) and tighten.

 S 434-033

 (11)
 Attach the fitting (1) to the expandable fitting (3) with lockwire.

 S 424-021

 (12)
 Install the antiskid transducer (Ref 32-42-11/401).

 S 434-022

 (13)
 Install the gravel protection shield.

 S 424-023

 (14)
 Install the clamp on the shield.

 TASK 32-11-87-404-034
 5.  AIRPLANES WITH BRAKE TEMPERATURE MONITORING WIRING; Main Landing Gear Electrical Harness Installation (Fig. 401)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(119)