B.
References
(1)
AMM 07-11-31/201, Jack Airplane Axles
(2)
AMM 29-15-00/204, Hydraulic Systems A and B
(3)
AMM 32-00-01/201, Ground Lockpins
C.
Access
(1)
Location Zone
310 Left Main Landing Gear
410 Right Main Landing Gear
D.
Prepare to Remove the Damper Assembly of the Main Landing Gear
S 214-002
(1)
Make sure that all the ground lockpins (AMM 32-00-01/201) are installed.
S 844-003
(2)
Remove the pressure from the hydraulic system A and the hydraulic reservoir (AMM 29-15-00/201).
S 034-004
(3)
Disconnect the hydraulic line from the damper, seal the line with a plug, and seal the damper with a cap.
E.
Remove the Damper Assembly of the Main Landing Gear
S 014-005
(1)
Remove the bolt that attaches the support bracket (5) of the electrical harness to the damper assembly (13).
(2)
Examine the washer and the flanged bushing (4).
(3)
Remove the checknut (6), the lockbolt (9), and the lock washer (7).
S 034-008
(4)
Disconnect the hydraulic line guides (12) from the damper and safety the hydraulic lines until they are clear of the torsion link.
(5)
Remove the apex nut (8) and the thrust washer (10).
S 214-006
S 024-007
S 024-009
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 401 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SHOCK STRUT DRAG STRUT
UPPER TORSION LINK1. 2. DAMPER BRACKET FLANGED BUSHING 4.
3. (EXAMPLE) ATTACHMENT BOLT DAMPER WASHER
6. CHECKNUT ELECTRICAL HARNESS SUPPORT BRACKET 5.
LOWER TORSION LINK HYDRAULIC RETURN 15. 14. LINE SEE B 11. APEX THRUST WASHER THRUST WASHER LOCKBOLT APEX NUT LOCKWASHER 10. 9. 8. 7.
12. HYDRAULIC LINE GUIDES
SEE A 13. DAMPER ASSEMBLY
16. BLEEDER PLUG
0.50 0.10 DAMPER HOUSING 19. BLEEDER PLUG 17. BLEEDER PLUG
HEAD OF DAMPER PISTON CAP 18. MANIFOLD
NUT GLAND PISTON
A B
Figure 401 Main Landing Gear Damper Installation
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-11-81
ALL ú ú 01 Page 402 ú Nov 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 584-010
(6)
Lift the main gear with an axle jack until the tires are off the ground (AMM 07-11-31/201).
S 844-011
(7)
Move apart the apex connection of the upper and lower torsion links (1, 15) as follows:
NOTE: This will help in the removal of the damper attachment bolt
____
(3).
(a)
Apply a forward and aft force to the wheels until the apex connetion of the upper and lower torsion links (1, 15) move apart.
(b)
Or, put a 2 X 4 wood beam between the shock strut and the outboard wheel and do the next step: 1) Hold the 2 x 4 wood beam at the 100-inch arm from the shock
strut centerline and slowly apply a counterclokwise pull until the apex connection of the upper and lower torsion links (1, 15) move apart.
S 024-012
(8)
Hold the torsion links and remove the damper attachment bolt (3).
S 024-013
(9)
Pull out the damper assembly (13), lift the upper torsion link (1) and remove the apex thrust washer (11).
TASK 32-11-81-404-014
3. Installation of the Damper to the Main Landing Gear (Fig. 401)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 1(105)
