locations.
(d)
If access is not necessary for subsequent tasks, install access panel No. 9 (AMM 28-11-11/401).
S 286-024
(10) For the area in the No. 2 fuel tank between rib No. 14 (rib at WS 453.00) and rib No. 15 (rib at WS 479.00), do these steps:
(a)
Remove access panel No. 10 (7412) on the right wing
(AMM 28-11-11/401).
(b)
Go into the opening for access panel No. 10 (AMM 28-10-00/201).
(c)
Do this task for all FQIS wiring and components between rib No. 14 and rib No. 15: FQIS Wiring and Component Visual Inspection. 1) Refer to drawing 65-48306 for wiring and component
locations.
(d)
If access is not necessary for subsequent tasks, install access panel No. 10 (AMM 28-11-11/401).
S 286-025
(11) For the area in the No. 2 fuel tank between rib No. 15 (rib at WS 479.00) and rib No. 16 (rib at WS 505.00), do these steps:
(a)
Remove access panel No. 11 (7413) on the right wing
(AMM 28-11-11/401).
(b)
Go into the opening for access panel No. 11 (AMM 28-10-00/201).
(c)
Do this task for all FQIS wiring and components between rib No. 15 and rib No. 16: FQIS Wiring and Component Visual Inspection. 1) Refer to drawing 65-48306 for wiring and component
locations.
(d)
If access is not necessary for subsequent tasks, install access panel No. 11 (AMM 28-11-11/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-44
ALL ú ú 01 Page 611 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 286-026
(12) For the area in the No. 2 fuel tank between rib No. 16 (rib at WS 505.00) and rib No. 17 (rib at WS 531.00), do these steps:
(a)
Remove access panel No. 12 (7414) on the right wing (AMM 28-11-11/401).
(b)
Go into the opening for access panel No. 12 (AMM 28-10-00/201).
(c)
Do this task for all FQIS wiring and components between rib No. 16 and rib No. 17: FQIS Wiring and Component Visual Inspection. 1) Refer to drawing 65-48306 for wiring and component
locations.
(d)
If access is not necessary for subsequent tasks, install access panel No. 12 (AMM 28-11-11/401).
TASK 28-41-44-286-027
5. FQIS, Center Tank - Inspection______________________________
A. References
(1)
AMM 28-10-00/201, Fuel Tanks
(2)
AMM 28-11-31/401, Center Tank Access Panel
(3)
DWG 65-48411, WING CENTER SECTION STA 540 - 663.76
B. Access
(1)
Location Zones
221 Center Section Fuel Tank
(2)
Access Panels
3303 A/C Access Panel
3304 A/C Access Panel
C. Procedure
S 286-028
(1) For the center fuel tank, do these steps:
(a)
Remove access panel for the center tank (AMM 28-11-31/401).
(b)
Go into the center tank (AMM 28-10-00/201).
(c)
Do this task for all FQIS wiring and components in the center tank: FQIS Wiring and Component Visual Inspection. 1) Refer to drawing 65-48311 for wiring and component
locations.
(d)
If access is not necessary for subsequent tasks, install the access panel for the the center tank (AMM 28-11-31/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-44
ALL ú ú 01 Page 612 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ISOLATED FUEL QUANTITY TRANSMITTER (IFQT) WIRE HARNESS - REMOVAL/INSTALLATION
_____________________________________________________________________________
1. General
_______
A. This procedure has instructions to remove and install the Isolated Fuel Quantity Transmitter (IFQT) wire harness.
B. The IFQT wire harness is divided into two sections, a section that runs between the IFQT and the pressure seal, and a section that runs from the pressure seal (external to the fuselage) to the fuel tank spar. Connectors are used on both ends.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 3(130)
