S 038-013

 (7)  
Remove the captive screw and the lockwasher from the terminal plug on the LO-Z cable.

 (a)  Keep these items for subsequent installation.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 AIRPLANES WITH FQIS WIRE HARNESSES THAT  ú 28-41-31
 ARE CRIMPED AND NOT SOLDERED  ú ú 01 Page 803 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 358-014
 (8)  Put a crimp in the terminal lug for the wire bundle with the AMP hand tool and the correct dies.
 NOTE: Tank units No. 83 and 90 are connected in a parallel
____ circuit at the No. 90 probe. The diameter of this terminal lug barrel is a small quantity more than the diameter of the other terminal lug barrels. Thus, you must use the blue die at this connection (not the crimp tool red die). The blue die is larger (14-16 gage) than the red die (18-22 gage) by a small quantity.
 (a)  Make sure the tool changed the shape of the end of the terminal lug barrel.
 S 438-015
 (9)
Install the captive screw and the lockwasher on the terminal plug.

 S 438-016

 (10)
 Connect the wire bundles and tighten the clamp on the compensator or the tank unit.

 (a) Tighten the screws or the nuts to these torque ranges:
 HI-Z cable (COAX) 15-16 pound-inches LO-Z cable (COAX) 19-23 pound-inches Strain relief clamp 7-9 pound-inches
 S 438-017
 (11) Install or tighten the clamps for the wire bundle that you removed or loosened before this step.
 E. Put the Airplane Back to Its Usual Condition
 S 418-018
 (1)  
Install the access panels that you removed (AMM 28-11-11/401, 28-11-31/401).

 S 868-020

 (2)
Close these circuit breakers and remove the DO-NOT-CLOSE tags:

 (a)  P6 Main Power Distribution Panel
 1) QTY
 2) EP GND FUELING

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 AIRPLANES WITH FQIS WIRE HARNESSES THAT  ú 28-41-31
 ARE CRIMPED AND NOT SOLDERED  ú ú 01 Page 804 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 828-027
 (3)  Do this Task: System Adjustment - Fuel Quantity Indicating System (AMM 28-41-00/501, 28-41-02/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 AIRPLANES WITH FQIS WIRE HARNESSES THAT  ú 28-41-31
 ARE CRIMPED AND NOT SOLDERED  ú ú 02 Page 805 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 TANK AND COMPENSATOR UNIT BUSSING PLUG - REMOVAL/INSTALLATION
_____________________________________________________________
 1.  General
_______
 A.  There are two tank and compensator unit bussing plugs, one for the No. 1 tank and one for the No. 2 tank. These bussing plugs are installed on the front spar. On some airplanes, there is also a bussing plug for the center tank, found on the rear spar in the wheel well area. The removal and installation procedures for each plug are the same, only the location is different (Fig. 401).
 TASK 28-41-41-004-001
 2.  Bussing Plug Removal (Fig. 401)
____________________
 A.  References
 (1)  AMM 27-81-00/201, Leading Edge Flap and Slat Control
 B.  Access
 (1)  Location Zones
 221 Center Section Fuel Tank
 305 Fuel Tank (Left)
 405 Fuel Tank (Right)

 C.  Procedure
 S 864-060
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 3(119)