A-A
CABLE SBA
CABLE SBB
WHEEL WELL
INPUT FORWARD WALL
ROD
RIG PIN S/B-2
SPOILER OUTPUT QUADRANT
SPEED BRAKE INPUT QUADRANT
FWD
B
Spoiler Mixer and Ratio Changer Linkage Figure 503 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-00
 ALL  ú ú 01 Page 509 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2) Adjust the tension in the cables to +10/-0 pounds of the tension shown in Fig. 501. 3) Install the locking clips on the turnbuckles.
 (i)  
Make sure the pressure seals in the left wheel well ceiling align with the cables SBA and SBB.

 (j)  
If the pressure seals do not align with the cables, adjust the position of the seals: 1) Remove the bolts that attach the pressure seals. 2) Move the seals to align with the cables. 3) Tighten the bolts that attach the seals.

 (k)  
Remove the rig pins S/B-1 and S/B-2.

 S 825-055
 (3)  
Adjust the ground spoiler control valve:

 (a)  
Install the rig pin S/B-1 in the forward drum quadrant (Fig. 502).

 (b)  
Install the rigging tool on the control valve to make sure the dimension A is 0.70 |0.01 inch (Fig. 504).

 (c)  
If the dimension A is not in the limit, adjust the input lever: 1) Remove the bolt that attaches the control rod to the valve

 lever. 2) Install the rigging tool on the valve lever. 3) Adjust the length of the control rod until you can easily
 install the bolt in the rod end. 4) Apply grease to the threads of the rod end. 5) Install the bolt, washer and nut to attach the control rod
 to the valve lever. 6) Install the cotter pin. 7) Tighten the checknut on the control rod. 8) Make sure you can see the rod end through the inspection
 hole in the control rod. 9) Remove the rigging tool from the valve lever. 10) Remove the rig pin S/B-1.
 S 825-012
 (4)  
Adjust the ground spoiler interlock valve:

 (a)  
Lift the airplane with the jacks until the right main gear shock strut is fully extended (AMM 07-11-11/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-00
 ALL  ú ú 01 Page 510 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL 
SEE  B 
SEE  A 
A 
CONTROL VALVE GROUND SPOILER 
DIMENSION "A" INCH 0.70 |0.01 VALVE LEVER RIG TOOL (MIT65-45116) 
CONTROL ROD  Figure 504 Ground Spoiler Control Valve Adjustment FWD INSPECTION HOLE CHECKNUT B 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-00
 ALL  ú ú 01 Page 511 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Make sure you can easily install the rig pin S/B-3 through the yoke of the interlock valve (Fig. 505).

 (c)  
If you cannot easily install the rig pin S/B-3, adjust the cable for the speed brake interlock valve. 1) Disconnect the protective boot from the spacer at the lower

 rod end:
 a) Remove the clamp from the protective boot.
 b) Move the protective boot away from the rod end.

 2) Remove the bolt that attaches the lower rod end to the
 torsion link. 3) Install the rig pin S/B-3. 4) Loosen the checknut on the lower rod end. 5) Adjust the lower rod end until you can easily install the
 bolt in the torsion link. 6) Make sure you can see the threads of the rod end through the inspection hole in the rod end. 7) Install the bolt, radius filler, washer and nut to attach
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(90)