B.
Access

 (1)  
Location Zone
 101, 102 Control Cabin
 205 Electrical Compartment

 C.
Prepare to Do the Flap 40-Unit Switches Operational Test

 S 865-013
 (1)  
Make sure these circuit breakers are closed:

 (a)  
P6 Panel
 1) FLAP LOAD RELIEF

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-94
 ALL  ú ú 02 Page 503 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-014
 (2)  Do this task: "Hydraulic System B Pressurization"
 (Ref 27-51-00/201).

 S 865-015
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH THE HYDRAULIC SYSTEMS PRESSURIZED, THE FLAPS WILL MOVE WHEN YOU MOVE THE FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (3)  Move the flap control lever to the 40-unit detent.
 NOTE: If the airplane is on jacks, compress the right main gear
____
 strut approximately 5 inches.

 D. Do the Test of the Flap 40-Unit Switches
 S 725-016
 (1)  
Move the flap load limiter test switch on the equipment bay light panel in the electronics compartment to the SYSTEM TEST position.

 (a)  
Make sure the flaps retract to the 30-unit position.

 S 725-017
 (2)  
Release the test switch.

 (a)  
Make sure the flaps extend to the 40-unit position.

 S 865-018
 (3)  
Put the flap control lever in the 30-unit position.

 (a)  
Make sure the flaps retract to the 30-unit position.

 S 725-019
 (4)
Move the flap load limiter test switch to the SWITCH TEST position

 (a)  
Make sure the TEST light is on.

 (5)
Put the flap control lever in the UP position to retract the flaps.

 S 865-021

 (6)  
Do this task: "Hydraulic System B Depressurization"
 (Ref 27-51-00/201).

 S 865-020
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-94
 ALL  ú ú 01 Page 504 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLAP CONTROL CABLE TENSION SWITCH - REMOVAL/INSTALLATION
________________________________________________________
 1.  General_______
 A.  There are three tasks in this procedure. There is a task for the removal, a task for the installation and a task for the functional test of the flap control cable tension switch.
 B.  The flap control cable tension switch is installed on the right side of the airplane below the passenger compartment floor above the aft cargo compartment. You must remove the forward right ceiling panel in the aft cargo compartment to get access to the tension switch.
 TASK 27-51-97-004-001
 2.  Flap Control Cable Tension Switch Removal_________________________________________
 A.  References
 (1)  
AMM 25-52-65/401, Cargo Compartment Ceiling Lining

 B.  
Access

 (1)  
Location Zone
 218 Aft Cargo Compartment

 C.  
Procedure

 S 864-002
 (1)
Open these circuit breakers and install DO-NOT-CLOSE tags:

 (a)  
P6-2 Panel
 1) FLAP POS IND - TE

 S 014-003
 (2)  
Do this task to remove the forward right ceiling panel in the aft cargo compartment: "Remove the Ceiling Lining" (AMM 25-52-65/401).

 S 024-004

 (3)  
Remove the flap control cable tension switch (Fig. 401):

 (a)  
Disconnect the wires at the splices near the switch.

 (b)  
Remove the nuts and washers that attach the switch to the mounting bracket.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 5(9)