B.
Access
(1)
Location Zone
101, 102 Control Cabin
C.
Prepare to Adjust the Flap 40-Unit Switches
S 015-002
(1)
Remove the right stabilizer trim wheel from the control stand:
(a)
Remove the retaining nut from the stabilizer trim wheel.
(b)
Remove the stabilizer trim wheel from the shaft.
NOTE: Do not remove the shaft.
____
S 015-003
(2)
Remove the upper right door from the control stand:
(a)
Remove the screws from the upper right door.
(b)
Turn the upper door up until you can get access to the wires for the lightplate.
(c)
Remove the wires for the lightplate.
(d)
Remove the door.
(e)
Replace the nuts and washers on the lightplate studs.
D.
Do the Flap 40-Unit Switches Adjustment
S 865-004
(1)
Move the flap control lever to the 30-unit detent.
(a)
Make sure the switches do not operate.
S 825-005
(2)
Move the flap control lever 5 |2 degrees aft of the 30-unit detent.
(a)
Make sure the switches operate: 1) You can hear a click when the switches operate. 2) You can use an ohmmeter to do a continuity check between
the switch terminals C and NO.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-94
ALL ú ú 01 Page 501 ú Mar 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
FLAP
HANDLE
INBD FWD
FLAP 40-UNIT SWITCHES
ACTUATOR
FLAP 40-UNIT SWITCHES A
RIGHT STABILIZER TRIM WHEEL
MOUNTING NUT AND WASHER (2 LOCATIONS)
Flap 40-Unit Switches Adjustment
Figure 501
UPPER RIGHT DOOR
RETAINING NUT
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-94
ALL ú ú 01 Page 502 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 825-006
(3)
If the switches did not operate, adjust the cam:
(a)
Remove the lockwire from the cam.
(b)
Loosen the bolts on the cam.
(c)
Adjust the cam to make the switches operate on the aft surface of the cam.
(d)
Tighten the bolts and install the lockwire.
S 415-007
(4)
Install the upper right door on the control stand:
(a)
Install the wires on the lightplate studs.
(b)
Install the door on the control stand.
(c)
Install the screws on the door.
S 415-008
(5)
Install the right stabilizer trim wheel on the control stand:
(a)
Put the stabilizer trim wheel on the shaft with the handle 90 +/-15 degrees from the left trim wheel handle.
(b)
Install the retaining nut on the trim wheel.
S 865-009
(6)
Put the flap control lever in the UP detent.
S 725-010
(7)
Do this task: "Operational Test - Flap 40-Unit Switches"
TASK 27-51-94-725-011
3. Operational Test - Flap 40-Unit Switches________________________________________
A. References
(1)
27-51-00/201, Trailing Edge Flap Systems
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(8)
