(e)  
Make sure the spoiler No. 7 aligns with the spoiler No. 6 in the limit of |0.25 inch.

 (3)  
Move the speed brake lever to the DOWN position.

 S 864-036

 (4)
Move the flap control lever to the UP detent to retract the flaps.

 I.
Do a Check of When the Spoilers Start to Extend

 S 864-035
 S 724-037
 (1)  
Turn the control wheel counterclockwise until the spoiler No. 2 starts to extend.

 (a)  
Make sure the control wheel is 11 |1 degrees counterclockwise from zero.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-51
 ALL  ú ú 02 Page 411 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 724-038
 (2)  
Turn the control wheel clockwise until the spoiler No. 6 starts to extend.

 (a)  
Make sure the control wheel is 11 |1 degrees clockwise from zero.

 J.
Put the Airplane Back to Its Usual Condition

 S 864-039
 (1)  
Turn the control wheel to the neutral position.

 S 864-040

 (2)
Remove the systems A and B hydraulic power (Ref 27-61-00/201).

 S 084-041

 (3)  
Remove the protractor and the protractor mount from the control wheel.

 S 084-042

 (4)
Remove the protractors and the protractor stands from the spoilers.

 (5)  
Remove the electrical power (Ref 24-22-00/201).

 (6)  
Fill the hydraulic reservoirs if it is necessary (Ref 12-12-00/301).

 S 864-043
 S 614-044
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-51
 ALL  ú ú 02 Page 412 ú Nov 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 FLIGHT SPOILER ACTUATOR - INSPECTION/CHECK
__________________________________________
 1.  General_______
 A.  There is one task in this procedure, an inspection of the flight spoiler actuator. To do the inspection, you measure the diameters of the bolt and bushings that attach the rod end of the actuator to the spoiler. You also measure the diameters of the parts that attach the spoiler actuator quadrant and the input lever.
 TASK 27-61-51-226-001
 2.  Flight Spoiler Actuator Inspection__________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0 to 1 inch

 B.  
References

 (1)  
AMM 27-61-51/401, Flight Spoiler Actuator

 C.  
Access

 (1)  
Location Zone 307, 407 Wing Trailing Edge Outboard Flaps and Spoilers

 D.  
Procedure

 S 026-002
 (1)  
Remove the flight spoiler actuator (Ref 27-61-51/401).

 S 226-003

 (2)  
Examine the bolts, bushings and bearings for worn areas (Fig. 601):

 (a)  
Remove the parts.

 (b)  
Use a micrometer to measure the parts.

 (c)  
Compare the dimensions you measured with the permitted dimensions shown in Fig. 601.

 (d)  
Repair or replace the parts that are not in the tolerance.

 (e)  
Install the parts.

 (3)  
Install the flight spoiler actuator (Ref 27-61-51/401).

 S 426-004
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-61-51
 ALL  ú ú 01 Page 601 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SPOILER ACTUATOR ROD END
FLIGHT SPOILER
A A
FWD
A
Flight Spoiler Actuator Wear Limits
Figure 601 (Sheet 1)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(68)