(d)  
Turn the guide tube to disconnect it from the lower rod end adapter.

 (e)  
Remove the lower rod end and lower rod end adapter.

 (f)  
Move the guide tube fully on the swivel tube.

 (g)  
Remove the collar from the cable.

 (h)  
Remove the guide tube.

 (i)  
Remove the bolt that attaches the upper rod end to the valve lever.

 (j)  
From the top end of the cable, pull the cable to remove it from the flexible tube.

 S 024-004
 (3)  
Remove the flexible tube:

 (a)  
Turn the captive bushings to disconnect the flexible tube from the two swivels.

 (b)  
Remove the cable guide adjacent to the landing gear trunnion.

 (c)  
Remove the two clamps from the wing structure and the three clamps on the drag strut.

 (d)  
Remove the flexible tube from the airplane.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-51
 ALL  ú ú 02 Page 401 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
CABLE
GUIDE

SEE A
CLAMP
(5 LOCATIONS) VALVE UPPER
LEVERSEE C ROD END
SEE B
BOLT
UPPER
SWIVEL

FLEXIBLE TUBE
RETAINER
CAPTIVE BUSHING
A
LOWER LOWERSEE E LOWERSWIVEL SWIVEL ROD
GUIDE  ROD ENDTUBE ENDTUBE CABLE COLLAR ADAPTERADAPTER
CAPTIVE  SPACER
PROTECTIVECLAMP
BUSHING  SEE D CLAMP
BOOT
B
Ground Spoiler Interlock Valve Cable Installation Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-51
 ALL  ú ú 01 Page 402 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
UPPER ROD INSPECTION END ADAPTER HOLE

Ground Spoiler Interlock Valve Cable Installation
Figure 401 (Sheet 2)

H65112
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-51
 ALL  ú ú 02 Page 403 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 024-005
 (4)  
Remove the swivel assemblies:

 (a)  
Remove the nut from the upper swivel.

 (b)  
Remove the upper swivel and the two washers.

 (c)  
Remove the clamp and the protective boot from the adapter.

 (d)  
Remove the two nuts from the lower swivel.

 (e)  
Remove the lower swivel and the two washers.

 TASK 27-62-51-404-006
 3. Ground Spoiler Interlock Valve Cable Installation (Fig. 401)
_________________________________________________
 A. General
 (1)  
If the new cable is fully assembled, you must disassemble it as shown in the removal procedure.

 B.
Consumable Materials

 (1)  
D00012 Grease, Silicone - DC33

 C.
References

 (1)  
27-62-51/501, Ground Spoiler Interlock Valve Cable

 (2)  
32-09-01/501, Main Landing Gear Safety Sensor

 D.
Access

 (1)  
Location Zone
 217 Right Main Wheel Well

 E.
Procedure

 S 644-007
 (1)  
Apply a thick layer of the grease to the flexible cable, swivel tubes, and guide tube.

 S 424-008

 (2)  
Install the swivel assemblies:

 (a)  
Install the washer on the lower swivel.

 NOTE: The length of the threads is longer on the lower swivel
____ than on the top swivel.
 (b)  
Install the lower swivel in the mounting bracket with the swivel tube down.

 (c)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(129)