S 034-009
(8) Remove the two-bolt couplings from the speed brake input shaft and the two mixer output shafts.
NOTE: You must keep the one-bolt coupling with the spoiler mixer.
____
S 034-010
(9)
Remove the pushrod from the spoiler mixer:
(a)
Remove the output lever for the pushrod from the spoiler mixer.
(b)
Remove the bolt that attaches the pushrod to the output lever.
(c)
Connect the output lever to the spoiler mixer.
(d)
Temporarily connect the pushrod to the ground spoiler control valve.
TASK 27-61-21-404-011
3. Spoiler Mixer Installation
__________________________
A. General
(1)
Make sure you have the correct part number of the spoiler mixer. Other spoiler mixers will install but they will not operate correctly.
B.
Special Tools and Equipment
(1)
MIT65-45116 Ground Spoiler Control Valve Rigging Tool
(2)
Rig Pin Kit - F70207-93:
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-21
ALL ú ú 02 Page 404 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
~........................................................................... | | | DIAMETER | LENGTH | | | REF NO. | F70207-( ) | (INCHES) | (INCHES) | FUNCTION | ............................................................................. | A/S-3 | -8 | 0.309-0.311 | 3.7 |0.25 | SPOILER CONTROL | | | | | | QUADRANT LOWER LEVEL | | A/S-4 | -11 | 0.309-0.311 | 6.7 |0.25 | AILERON BUS DRUM | | A/S-14 | -11 | 0.309-0.311 | 6.7 |0.25 | SPOILER MIXER | | S/B-2 | -13 | 0.309-0.311 |2.35 |0.06 | SPEED BRAKE INPUT | | | | | | QUADRANT | 2.........…............….............…............….........................1
C. Consumable Materials
(1)
D00633 Grease BMS 3-33 (Recommended)
(2)
D00013 Grease MIL-G-23827 (Alternate)
D.
References
(1)
27-61-00/201, Spoiler Control System
(2)
27-61-21/501, Spoiler Mixer
E.
Access
(1)
Location Zone
216, 217 Main Wheel Well
F.
Procedure
S 434-012
(1)
Connect the pushrod to the spoiler mixer (Fig. 401):
(a)
Remove the output lever for the pushrod from the spoiler mixer.
(b)
Put the pushrod in the position where you can connect the fixed rod end to the spoiler mixer.
(c)
Install the rod end bolt with the head to the side of the mixer.
(d)
Install the washer and nut on the bolt.
(e)
Tighten the nut to 50-70 pound-inches.
(f)
Connect the output lever and the pushrod assembly to the spoiler mixer.
S 864-013
(2)
Make sure the speed brake lever is in the DOWN position.
S 824-014
(3)
Make sure you can easily install the rig pin S/B-2 in the speed brake input quadrant.
(a)
Remove the rig pin S/B-2.
S 424-015
(4)
Install the spoiler mixer:
(a)
Connect the two-bolt couplings to the ratio changer: 1) Put the couplings in the position shown in Fig. 401. 2) Install the washers and nuts on the bolts. Do not tighten
the nuts.
(b)
Remove the rig pin A/S-14 from the spoiler mixer.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-61-21
ALL ú ú 03 Page 405 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(c)
Install the one-bolt coupling on the mixer: 1) Make sure the end of the coupling with the bolt is on the aileron input shaft on the spoiler mixer. 2) Install the bolt on the outboard side of the input shaft with the head up.
3) Install the washer and nut on the bolt. Do not tighten the nut. 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(45)
