曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

T81264
A
737-300/400/500MAINTENANCE MANUAL
 TRAILING EDGE FLAP POSITION INDICATING SYSTEM - TROUBLE SHOOTING
________________________________________________________________
 1.  General_______
 A.  All trouble shooting procedures are based on the assumption that wiring is OK and that electrical power is available. If corrective action in the procedure does not correct the problem, check wiring using the wiring diagram.
 B.  The trailing edge flap system must be properly adjusted prior to trouble shooting the trailing edge flap position indicating system.
 2.  Prepare for Trouble Shooting____________________________
 A.  Provide electrical power.
 B.  Check that TRAILING EDGE FLAP POS IND circuit breaker is closed.
 C.  Check that FLAP SHUT-OFF VALVE circuit breaker is closed.
 D.  Provide system B hydraulic power (Ref 27-51-00, MP).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-58-01
 ALL  ú ú 01 Page 101 ú Jun 25/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
TROUBLE  PROBABLE CAUSE  ISOLATION PROCEDURE  REMEDY 
not within tolerance zone Indicator pointer Indicator pointer for one flap does not move when flaps move  indicator defective Flaps are not properly Flap position transmitter out of adjustment Flap position transmitter extending defective Flap position  Check for 28V AC at transmitter plug pin 11 Visually inspect flap position that pointer is within tolerance zone at flaps up Retract flaps and check Check for 28V AC at indicator plug pin 5 (left indicator) or pin 2 (right indicator  Replace transmitter Adjust transmitter (AMM 27-58-41/401) Adjust flap drive system Repair wiring or Repair wiring or Replace indicator 
functioning Flap asymmetry test switch not  between pin 3 and 8 Check switch for continuity and pin 2 and 7 (left flaps) or between pin 4 (right flaps) and 9 and pin 5 and 10  Replace switch 

Trailing Edge Flap Position Indicating System Trouble Shooting Chart Figure 101
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-58-01
 ALL  ú ú 01 Page 102 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 TRAILING EDGE FLAP POSITION INDICATING SYSTEM - ADJUSTMENT/TEST
_______________________________________________________________
 1.  General
_______
 A.  There is one task in this procedure, a functional test of the position indicating system for the trailing edge flaps. You must make sure the trailing edge flap system is adjusted correctly before you do the test of the position indicating system.
 TASK 27-58-01-725-001
 2.  Trailing Edge Flap Position Indicating System Functional Test
_____________________________________________________________
 A.  References
 (1)  
24-22-00/201, Manual Control

 (2)  
27-32-00/501, Stall Warning System

 (3)  
27-51-00/201, Trailing Edge Flap System

 (4)  
27-51-00/501, Trailing Edge Flap System

 B.  
Access

 (1)  
Location Zone
 101, 102 Control Cabin

 C.  
Procedure

 S 865-002
 (1)  
Supply the electrical power (Ref 24-22-00/201).

 S 865-003

 (2)  
Supply the system B hydraulic power (Ref 27-51-00/201).

 S 825-004

 (3)  
Make sure the trailing edge flap system is adjusted correctly (Ref 27-51-00/501).

 (4)
Put the flap control lever in the UP detent to retract the flaps.

 (5)
Examine the pointers on the flap position indicator (Fig. 501):

 S 865-005
 S 725-006
 NOTE: Lightly hit the position indicator with your finger to remove
____
 the friction error.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 5(12)