曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

737-300/400/500MAINTENANCE MANUAL
 (5)  S 494-006Install the stabilizer trim lock.
 (6)  S 014-007Open the access door 3701.
 (7)  S 014-008Remove the access panel 9105 or 9205 and the end side door.
 (8)  S 014-009Remove the lower rear spar and the gap covers to get access to the hinge.
 (9)  S 864-010Hold the stabilizer structure and the center section assembly in the area of the hinge components. (a) Make sure all the components align correctly during the removal.
 S 024-011

 (10)
 Remove the hinge housing fitting of the center section hinge (Fig. 402):

 (a)  
Remove the cotter pins, the nut (7), and the washer (8).

 (b)  
Remove the nut (6) and the bushing spacer (5).

 (c)  
Remove the bushing retainer (10).

 (d)  
Install the washer (8) and the nut (7).

 (e)  
Use the punch set and push out the parts as follows: 1) Hinge pin (1) 2) Bushing retainer (13) 3) Hinge pin (2)

 (f)  
Remove the two hinge bushings (9 and 12).

 (g)  
If a bushing spacer (3) is used, it will come off with the adjustable hinge bushing (12) when you remove the hinge bearing on the right side.

 (h)  
Remove the two bolts to remove the upper thrust brace (15).

 NOTE: Make marks on the upper thrust brace to help make
____ the installation easier.
 (i)  Remove the two bolts to remove the lower thrust brace (14).
 NOTE: Make marks on the lower thrust brace to help make
____ the installation easier.
 (j)  Remove three bolts to remove the thrust brace attach fitting (16) and the filler
 NOTE: Make marks on the attach fitting to help make the
____
 installation easier.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-31
 ALL  ú ú 01 Page 406 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (k)  Remove the three bolts to remove the fail-safe links (17 and 19) and the shims.
 NOTE: Make marks on the fail-safe links to help make the
____ installation easier, and write the thickness and the location of the shims.
 (l)  
Remove six fasteners to remove the upper channel spacer and the upper plate spacer (22 and 21) together as an assembly.

 (m)  
Remove six fasteners to remove the lower channel spacer and the lower plate spacer (24 and 23) together as an assembly.

 (n)  
Remove the two bolts (25) to remove the hinge housing fitting (18).

 TASK 27-41-31-404-012
 3.  Horizontal Stabilizer Center Section Hinge Fitting Installation (Fig. 402)._______________________________________________________________
 A. Special Tools and Equipment
 (1)  
F80183-1 - Horizontal Stabilizer Thread Protector

 (2)  
F71336-501 - Stabilizer Trim Lock

 B.
Standard Tools and Equipment

 (1)  
Dial Indication Depth Gage

 C.
Consumable Materials

 (1)  
D00013 - Grease - BMS 3-24

 D.
Access

 (1)  
Location Zone
 701 Tail Compartment
 709 Horizontal Stabilizer, LH
 710 Horizontal Stabilizer, RH

 (2)  
Access Panels
 3701 Stabilizer Trim Access Door
 9105 Access Panel Trailing Edge, LH
 9205 Access Panel Trailing Edge, RH

 E.
Procedure

 S 424-028
 CAUTION:_______DO NOT PUT A LOAD ON THE BEARING. YOU CAN CAUSE DAMAGE TO THE STABILIZER.
 (1)  
Install the hinge housing fitting (18):

 (a)  
Set the hinge housing fitting (18) in its position. 1) Install the two bolts (25).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-31
 ALL  ú ú 01 Page 407 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 
737-300/400/500MAINTENANCE MANUAL
 (b)  Install the fail-safe links (17 and 19) and the fillers with three bolts.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(97)