EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-91
ALL ú ú 01 Page 409 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
5) AUTO FLT CONT SYS A SNSR EXC AC
6) AUTO FLT CONT SYS A FCC DC
7) AUTO FLT CONT SYS A ENGAGE INTLK A
8) AUTO FLT CONT SYS A WARN LIGHT BAT
S 094-012
(8)
Remove the stabilizer trim lock.
S 434-017
(9)
Connect the electrical connectors D700 and D381.
S 864-018
(10)
If the hydraulic power is not necessary, do this task: "Put the Airplane Back to the Condition Before the Pressure Removal" (Ref 27-31-00/201).
S 824-016
(11)
Adjust the neutral shift mechanism in this task: "Adjustment -Elevator and Tab Control System" (Ref 27-31-00/501).
S 714-015
(12)
Do this task: "System Test - Neutral Shift Operation" (Ref 27-31-00/501).
(13)
Close the access door 3701.
(14)
Install the access panel 3802.
S 414-014
S 414-013
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-91
ALL ú ú 01 Page 410 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
FEEL SYSTEM PITOT TUBE - REMOVAL/INSTALLATION
_____________________________________________
1. General_______
A. This procedure has two tasks, one for the removal and one for the installation of the feel system pitot tube (which is referred to as the "pitot tube"). The procedure has these parts:
(1)
The removal of the pitot tube
(2)
The installation of the replacement pitot tube.
TASK 27-31-94-004-001
2. Feel System Pitot Tube Removal______________________________
A. Access
(1)
Location Zone
706 Vertical Stabilizer
(2)
Access Panels
9525 Access Door Between Fin
B.
Procedure
(1)
Remove the access panel 9525.
S 014-002
Feel System Pitot Tube Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-94
ALL ú ú 01 Page 401 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 024-003
(2)
Remove the pitot tube (Fig. 401)
(a)
Set the PITOT STATIC switches on the P5 Pilots Overhead Panel to OFF and attach DO-NOT-MOVE tags.
CAUTION:_______DO NOT TOUCH THE PITOT TUBE. LET THE TEMPERATURE DECREASE TO AMBIENT BEFORE YOU REMOVE THE PITOT TUBE. IF YOU TOUCH THE PITOT TUBE WHEN IT IS HOT, IT CAN BURN YOU.
(b)
Disconnect the electrical connector D692 or D694.
(c)
Disconnect the pitot air connector.
(d)
Hold the pitot tube and remove the three mounting bolts.
(e)
Remove the pitot tube, the gasket, and the wedge.
(f)
Install the protective cap on the pitot air line.
TASK 27-31-94-404-007
3. Feel System Pitot Tube Installation (Fig. 401)___________________________________
A. Consumable Materials
(1)
A00303 Adhesive - RTV 174 (Recommended)
(2)
A00247 Sealant, Pressure and Environmental-Chromate Type - BMS5-95 (Optional)
(3)
A00900 Sealant, Silicone, RTV - Dow Corning 93-006 (Optional)
B.
References
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(21)
