曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

A 737-300/400/500MAINTENANCE MANUAL
 S 424-025
 (3)  Install bearings in the end fittings of the output torque tube.
 S 424-027
 (4)  Put and hold the output torque tube at aft bulkhead.
 S 424-014
 (5)  Install the pivot bolts in the outboard pivot brackets:
 (a) Apply grease to the shank of each bolt.
 (b) Hold the torque tube in its position.
 (c) Install the pivot bolts with the bolt heads inboard.
 (d) Install the nut and the washer at each bolt.
 (e) Tighten the nut to standard torque.
 S 434-011
 (6)  Install the pivot bolts in the inboard pivot brackets by pushing the
 alignment pins out:
 CAUTION: BE CAREFUL WHEN YOU INSTALL THE PIVOT BOLTS. YOU CAN_______
 CAUSE DAMAGE TO BEARING COMPONENTS IF YOU HIT THE PIVOT
 BOLTS DURING THE INSTALLATION.
 (a) Apply grease to the shank of each bolt.
 (b) Install the pivot bolts with the bolt heads inboard.
 (c) Install the washer and the first locknut.
 (d) Tighten the first locknut to 500-600 pound-inches.
 CAUTION: DO NOT TRY TO TIGHTEN THE FIRST LOCKNUTS AGAIN AFTER YOU_______
 TIGHTEN THE SECOND LOCKNUTS. IF YOU TIGHTEN THE FIRST
 LOCKNUTS AGAIN, YOU CAN CAUSE DAMAGE TO EQUIPMENT.
 (e) Install the washer and the second locknut.
 (f) Tighten the second locknut to 150-220 pound-inches.
 S 434-028
 (7)  Install the PCU upper mounting bolts to the touque tube.
 S 434-004
 (8)  Install the mounting brackets of the autopilot elevator actuators.
 S 434-022
 (9)  Install the autopilot elevator actuators (Ref 22-11-26/401).
 S 414-005

 (10)
 Install the tail cone (Ref 53-53-00/401).

 S 824-006

 (11)
 Adjust the elevator control pushrods in this task:  "Adjustment -Elevator and Tab Control System" (Ref 27-31-00/501).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-74
 ALL  ú ú 03 Page 404 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 864-009
 (12)
 Do this task:  "Put the Elevator Hydraulic Systems A and B Back to the Condition Before the Pressure Removal" (Ref 27-31-00/201).

 S 414-010

 (13)
 Close the access door 3802 (Ref 12-31-41/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-74
 ALL  ú ú 03 Page 405 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 ELEVATOR OUTPUT TORQUE TUBE - INSPECTION/CHECK
______________________________________________
 1.  General_______
 A.  This subject has one task. The task is an inspection of the elevator output torque tube (which is referred to as the "torque tube"). The procedure has these parts:
 (1)
The removal of the torque tube

 (2)
An inspection of the torque tube

 (3)
The installation of the torque tube.

 TASK 27-31-74-206-001
 2.  Elevator Output Torque Tube Wear Limits Inspection (Fig. 601)__________________________________________________
 A.  Standard Tools and Equipment
 (1)
Micrometer - 0-1 inch

 (2)
Vernier Caliper

 B.  
References

 (1)
27-31-74/401, Elevator Output Torque Tube

 C.  
Access

 (1)  
Location Zone
 701 Area 1 Tail Compartment

 

C 
C 
D 
B  D 
B 
A 
A 
SEE  A 

A
Elevator Output Torque Tube Wear Limits Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(9)