EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-04
ALL ú ú 01 Page 406 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
0.12
INCH
B-B
0.06
C-C
1 FILL THE CLEARANCE WITH BMS 5-95 IF THE CLEARANCE EXCEEDS 0.06 INCH
MEASURE AT THE INBOARD AND
OUTBOARD ENDS OF THE FLAP
0.06 |0.04 INCH 0.06 |0.04 INCH MIDFLAP
INBOARD FLAP OUTBOARD FLAP
OUTBOARD FLAP TRACK FAIRING TRACK FAIRING
D-D
URATION CONFIG-AIRPLANE (INCHES) SPOILER-TO-MIDFLAP CLEARANCE EDGE-TO-PANEL TRAILING UPPER WING (INCHES) MIDFLAP CLEARANCE2
ACTUATOR AT OUTBOARD ACTUATOR AT INBOARD
NO FUEL ON JACKS 0.03 +0.10/-0.00 0.03 +0.10/-0.00 0.03 +0.10/-0.00
NO FUEL ON GEAR 0.03 +0.10/-0.00 0.08 +0.10/-0.00 0.08 +0.10/-0.00
FULL FUEL ON GEAR 0.03 +0.10/-0.00 0.13 +0.10/-0.00 0.13 +0.10/-0.00
Inboard Trailing Edge Flap to Wing Adjustment
Figure 402 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-51-04
ALL ú ú 01 Page 407 ú Mar 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
B.
C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
(4)
Protractor Assembly - MIT65B80307-1 (Preferred)
(5)
Protractor Assembly - F52485-500 (Optional)
(6)
Trailing Edge Flaps Sling Assembly - F80213-73
(7)
Flap Drive Screw Support Assembly - F80057-1Consumable Materials
(1)
C00259 Primer - BMS 10-11, Type I
(2)
C00308 Corrosion Preventive Compound - MIL-C-11796, Class 3
(3)
A00247 Sealant - BMS 5-95References
(1)
27-51-00/201, Trailing Edge Flap System
(2)
27-51-00/501, Trailing Edge Flap System
(3)
27-51-04/501, Inboard Trailing Edge Flap
(4)
27-51-04/601, Inboard Trailing Edge Flap
(5)
27-51-07/401, Inboard Foreflap
(6)
27-51-29/401, Inboard Midflap Seal Plate
(7)
27-51-32/401, Inboard Flap Track Fairing
(8)
27-61-00/501, Speed Brake Control SystemAccess
(1)
Location Zone 101, 102 Control Cabin 309, 409 Wing Trailing Edge Inboard Flap and Spoiler
Install the Inboard Flap
S 224-016
(1)
If you will install used parts, do this task: "Inboard Flap Inspection" (Ref 27-51-04/601).
S 214-017
(2)
Make sure the rig pins are installed in the boom.
S 824-018
(3)
If you disconnected the aftflap drive system, do this task: "Inboard Trailing Edge Flap Adjustment" (Ref 27-51-04/501).
S 424-019
(4)
Install the inboard flap:
(a)
Remove the forward roller (2) from the side of the carriages.
(b)
Remove the cross beam (3) from the outboard carriage.
(c)
Install the sling to hold the flap.
(d)
Align the midflap carriages with the flap tracks.
(e)
Move the flap forward on the track until it is in the retracted position.
(f)
Install the foreflap toggle stop (5) on the top of each flap track (6).
(g)
Install the midflap carriage stop (7): 1) Put the carriage stop in the flap track. 2) Apply the corrosion preventive compound on the bolts. 3) Install the bolt and nut to attach the carriage stop to the
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(170)
