FWD WASHER
PACKINGS
B
TYPICAL VALVE INSTALLATION
NOTE: ISOLATION VALVES NO. 1
THRU NO. 6 ARE SHOWN

C
POSITIONED OPEN.
Manual Isolation Valve Installation
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-87
 ALL  ú ú 01 Page 402 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 TASK 27-31-87-404-004
 3.  Manual Isolation Valve Installation (Fig. 401)___________________________________
 NOTE: Do not change a Ronson with a Whittaker or the Whittaker with a Ronson
____ valve handle. If you change the valve handle on a valve, the position of the valve handle will not agree with the position of the valve. This can cause a loss of the hydraulic power.
 A. Consumable Materials
 (1)  
D00054 Lube, Skydrol Assembly - MCS 352

 (2)  
G00062 Fluid - Hydaulic, Fire Resistance, BMS 3-11

 B.
References

 (1)  
12-12-00/301, Hydraulic Reservoirs

 (2)  
12-31-41/201, Body Section 48 Access Doors and Panels

 (3)  
27-31-00/201, Elevator and Tab Control System

 (4)  
27-31-84/501, Isolation Valves Hydraulic Module

 C.
Access

 (1)  
Location Zone
 702 Area 2 Tail Compartment Access Door

 (2)  
Access Panels
 3701 Stabilizer Trim Access Door

 D.
Procedure

 S 864-006
 (1)  
Do this task: "Remove the Elevator Hydraulic Systems A and B" (Ref 27-31-00/201).

 S 644-014

 (2)  
Lubricate the packings and the valve lightly with assembly lube or hydraulic fluid.

 (3)  
Install the packings and the backup rings on the valve.

 S 424-016

 (4)  
Install the valve on the module:

 (a)  
Remove the plugs from the module.

 (b)  
Attach the valve with four mounting bolts.

 (c)  
Install the lockwires on the bolts.

 S 434-015
 S 864-007
 (5)  Do this task: "Put the Elevator Hydraulic Systems A and B Back to the Condition Before the Pressure Removal" (Ref 27-31-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-87
 ALL  ú ú 01 Page 403 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (6)  S 874-008Move the control column or the rudder pedals to bleed the hydraulic lines.
 (7)  S 794-009Visually examine the valve for hydraulic leaks.
 (8)  S 714-010Do this task: "Isolation Valves Hydraulic Module" (Ref 27-31-84/501).
 (9)  S 864-011Make sure all the valve handles are in the OPEN position.
 S 414-013

 (10)
 Turn the locking bar down.

 (a)  
Install the lower mounting bolts and the washers.

 S 414-017
 (11)
 Close the access door 3701 (Ref 12-31-41/201).

 S 614-012

 (12)
 If it is necessary, do this task:  "Service Hydraulic Reservoirs" (Ref 12-12-00/301).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-87
 ALL  ú ú 01 Page 404 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 ELEVATOR NEUTRAL SHIFT MECHANISM - REMOVAL/INSTALLATION
_______________________________________________________
 1.  General
_______
 A.  This procedure has two tasks, one for the removal and one for the installation of the elevator neutral shift mechanism (which is referred to as the neutral shift mechanism). The procedure has these parts:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(17)