(a)  
P6 Panel
 1) AUTOSLAT 1 DC
 2) AUTOSLAT 2 DC
 3) SMC 2 SNSR EXC AC
 4) SMC 2 CMPTR DC

 (b)  
P18 Panel
 1) L ALPHA VANE HTR
 2) R ALPHA VANE HTR
 3) SMC 1 SNSR EXC AC
 4) SMC 1 CMPTR DC
 5) SMC STALL WARN ASYM MODE

 S 014-039-002
 (2)  Remove the applicable sidewall panel adjacent to the captain's or the first officer's seat to get access to the AOA sensor.
 S 034-027-002
 WARNING: MAKE SURE THAT THE AOA SENSOR VANE IS COOL BEFORE YOU TOUCH IT.
_______
 THE HEAT OF THE VANE CAN BURN YOU.

 CAUTION:_______DO NOT APPLY FORCE TO THE AOA SENSOR VANE. YOU CAN DAMAGE THE AOA SENSOR IF YOU APPLY FORCE TO THE VANE OR SPIN THE SENSOR.
 (3)  
Remove the 8 mounting screws at the sensor.

 S 024-029-002

 (4)  
Disconnect the electrical connector from the sensor.

 (5)  
Move the sensor from side to side to loosen it.

 (6)  
Remove the sensor.

 S 024-030-002
 S 024-031-002
 TASK 27-32-11-404-025-002
 3. Angle of Airflow Sensor Installation (Fig. 401)
____________________________________
 A. Special Tools and Equipment
 (1)  
Portable Calibrator - F72786-181

 B.
Consumable Materials

 (1)  
A00247 Adhesive - BMS 5-95, Class B

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 AIRPLANES WITH STALL MANAGEMENT COMPUTER ú

 27-32-11

 P/N 65-52822  ú  CONFIG  2
 ú  02  Page 402
 ú  Jul 15/97 

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
References
 (1)  
AMM 22-11-38/501, Angle of Airflow Sensor

 (2)  
AMM 24-22-00/201, Manual Control

 (3)
AMM 30-31-00/501, Alpha vane heater testAccess

 (1)  
Location Zone

 101, 102 Control CabinInstallation Procedure
 S 424-032-002
 (1)  
Carefully insert the sensor vane through the fairing from inside the control cabin.

 S 424-033-002

 (2)  
Install the sensor with the gasket, the filler ring, and the 8 mounting screws.

 S 824-034-002

 (3)  
Make sure that the face of sensor aligns with the fuselage outer skin by |0.02 inches or less.

 (a)  
If the sensor does not align with the skin, adjust the filler ring: 1) Remove laminations from the filler ring to make it thinner,

 or replace the filler ring to make it thicker.
 WARNING: DO NOT LET ADHESIVE GET ON THE ANGLE OF AIRFLOW
_______ SENSOR. ADHESIVE CAN JAM THE ANGLE OF AIRFLOW SENSOR.
 2) If you install a new filler ring, bond it to the inner face of the skin doubler. 3) Make sure you apply a minimum of 0.0005 inch of adhesive to to the mating surfaces.
 NOTE: You can possibly apply 0.010 to 0.030 inch of
____ adhesive to seal correctly.
 S 424-035-002
 (4)  
Connect the electrical connector to the sensor.

 (5)  
Install the sidewall panel.

 S 864-037-002

 (6)  
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6 Panel
 1) AUTOSLAT 1 DC
 2) AUTOSLAT 2 DC
 3) SMC 2 SNSR EXC AC
 4) SMC 2 CMPTR DC

 S 414-036-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
 AIRPLANES WITH STALL MANAGEMENT COMPUTER ú

 27-32-11

 P/N 65-52822  ú  CONFIG  2
 ú  02  Page 403
 ú  Nov 12/00 

BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(60)