S 864-002
 CAUTION:_______REFER TO AMM 20-40-12/201 BEFORE YOU TOUCH THE DSWC. THE DSWC IS STATIC SENSITIVE. STATIC DISCHARGE CAN CAUSE DAMAGE TO DEVICES IN THE DSWC.
 (3)  
Follow the procedure for electrostatic discharge sensitive devices (AMM 20-40-12/201).

 (4)  
Loosen the knob and remove the DSWC from the E1-1 shelf.

 S 024-013
 TASK 27-32-41-404-005
 3.  Digital Stall Warning Computer Installation___________________________________________
 A.  References
 (1) AMM 20-40-12/201, Electrostatic Discharge Sensitive Devices
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH DIGITAL STALL WARNING ú

 27-32-41
 COMPUTER P/N 65-52819  ú ú 02 Page 401 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Stall Warning Computer
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH DIGITAL STALL WARNING ú

 27-32-41
 COMPUTER P/N 65-52819  ú ú 05 Page 402 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.

A
737-300/400/500MAINTENANCE MANUAL
 (2)
AMM 24-22-00/201, Manual ControlAccess

 (1)  
Location Zone 205 Electronic Compartment

 (2)  
Access Panel

 1201 Electronic Equipment Access DoorDSWC Installation
 S 864-006
 CAUTION:_______REFER TO AMM 20-40-12/201 BEFORE YOU TOUCH THE DSWC. THE DSWC IS STATIC SENSITIVE. STATIC DISCHARGE CAN CAUSE DAMAGE TO DEVICES IN THE DSWC.
 (1)  
Follow the procedure for electrostatic discharge sensitive devices (AMM 20-40-12/201).

 S 424-007

 (2)  
Install the DSWC on the E1-1 shelf and tighten the knob.

 NOTE: Be careful not to cause damage to the electrical connectors
____
 on the back of the DSWC.

 S 864-008
 (3)  
If you replaced DSWC 1, close these circuit breakers on the P18 panel:

 (a)  
STALL WARN 1 AC

 (b)  
STALL WARN 1 DC

 S 864-014
 (4)  
If you replaced DSWC 2, close these circuit breakers on the P6 panel:

 (a)  
STALL WARN 2 AC

 (b)
STALL WARN 2 DCDSWC Test

 (1)  
Supply electrical power (AMM 24-22-00/201).

 S 744-010

 (2)  
Do a BITE test of the DSWC:

 (a)  
Push and hold the START BITE switch on the front of the applicable DSWC:

 (b)  
Make sure that all lights on the computer come on for 2 to 4 seconds.

 S 864-009
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH DIGITAL STALL WARNING ú

 27-32-41
 COMPUTER P/N 65-52819  ú ú 02 Page 403 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (c)  
Release the START BITE switch.

 (d)  
Look to see if one or more lights stays on after 4 seconds.

 NOTE: If a light stays on after 4 seconds, the computer
____ memory holds a real-time failure for that function.
 S 074-012
 (3)  
If a light stayed on in the BITE test, erase the DSWC fault memory (after you correct the specific failure):

 (a)  
Push and hold the START BITE switch.

 (b)  
Make sure that all lights on the DSWC come on for 2 to 4 seconds.

 (c)  
Look to see if one or more lights stays on after 4 seconds.

 NOTE: If a light stays on after 4 seconds, the computer memory
____ holds a failure for that function. The light will go off after approximately 25 seconds.
 (d)  
When one or more lights starts to flash after 10 to 20 seconds, release the START BITE switch. The memory is now clear.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(65)