曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (1)  Examine the AOA sensor vane for deformation, nicks, or pits of the vane leading edge.
 NOTE: There will be some erosion of the vane leading edge after
____ several thousand flight hours. This is permitted.
 S 906-003
 (2)  
If the AOA sensor has one or more of these conditions, replace the sensor (AMM 27-32-11/401):

 (a)  
Asymmetrical erosion of the upper and lower surfaces of the vane.

 (b)  
Asymmetrical pattern of nicks on the vane.

 (c)  
Deterioration of the sensor index pins.

 (d)  
A bent vane shaft.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-32-11
 ALL  ú ú 02 Page 601 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Angle of Airflow Sensor Check
Figure 601

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-32-11
 ALL  ú ú 02 Page 602 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 986-004
 (3)  
Slowly turn the AOA sensor between its stops (approximately 70°).

 (a)  
Make sure that only light torque is necessary to turn the sensor.

 (b)  
Make sure that there is no change in the torque.

 (c)  
If there is too much friction when you turn the vane, replace the AOA sensor (AMM 27-32-11/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-32-11
 ALL  ú ú 01 Page 603 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STALL WARNING TEST MODULE - REMOVAL/INSTALLATION
________________________________________________
 1.  General_______
 A. This procedure has two tasks:
 (1)  
Stall Warning Test Module Removal

 (2)  
Stall Warning Test Module Installation

 TASK 27-32-21-004-001
 2.  Stall Warning Test Module Removal (Fig. 401)_________________________________
 A. Access
 (1)  
Location Zone
 101, 102 Control Cabin

 B.
Procedure

 S 864-012
 (1)  
AIRPLANES WITH DIGITAL STALL WARNING COMPUTER P/N 65-52819; Open these circuit breakers:

 (a)  
P6 Panel
 1) STALL WARN 2 AC

 

Stall Warning Test Module
Figure 401

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-32-21
 ALL  ú ú 01 Page 401 ú Jul 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2) STALL WARN 2 DC
 (b)  P18 Panel
 1) STALL WARN 1 AC
 2) STALL WARN 1 DC

 S 864-013
 (2)  
AIRPLANES WITH STALL MANAGEMENT COMPUTER P/N 65-52822; Open these circuit breakers:

 (a)  
P6 Panel
 1) SMC 2 CMPTR DC

 (b)  
P18 Panel
 1) SMC 1 CMPTR DC

 

 S 024-005
 (3)  
Remove the module:

 (a)  
Hold the module.

 (b)  
Release the 4 fasteners which attach the module to the aft overhead panel.

 (c)  
Lower the module from the aft overhead panel.

 (d)  
Disconnect the electrical connectors from the back of the module.

 (e)  
Remove the module.

 TASK 27-32-21-404-016
 3.  Stall Warning Test Module Installation (Fig. 401)______________________________________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(62)