曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (m)  Install the left flap position transmitter (Fig. 506): 1) Apply a layer of the grease to the splines on the input
 shaft. 2) Put the transmitter in its position on the gearbox.
 NOTE: Make sure the two pointers stay aligned.
____
 3) Apply a layer of the primer to the bolts and washers. 4) With the primer wet, install the bolts and washers to attach the transmitter to the gearbox.
 5)  Make sure the bonding resistance between the transmitter and the gearbox is not more than 0.0025 ohm (SWPM 20-20-00).
 S 735-049
 (7)  
Do the test again with the right asymmetry shutoff system.

 S 865-050

 (8)  
Supply the system B hydraulic power (AMM 27-51-00/201).

 S 865-051

 (9)  
Move the flap control lever to the UP detent to retract the flaps.

 (a)  
Stop for 2 minutes to permit the flaps to fully retract.

 S 865-052
 (10)
 Remove the system B hydraulic power (AMM 27-51-00/201).

 S 715-053

 (11)
 Do the test of the flap asymmetry circuit.

 (a)  
Put the asymmetry test switch in the L position (Fig. 507). 1) Make sure the asymmetry test light is on. 2) Make sure the left pointer on the flap position indicator

 moves 22 |5 degrees (a chordal dimension of 0.17 to 0.28 inch between the two pointers). 3) Make sure the flap bypass valve moves to the position 2.

 (b)  
Release the asymmetry test switch. 1) Make sure the asymmetry test light is off. 2) Make sure the flap bypass valve moves to the position 1.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 03 Page 523 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 3) Make sure the two pointers align.
 (c)  
Put the asymmetry test switch in the R position. 1) Make sure the asymmetry test light is on. 2) Make sure the right pointer on the flap position indicator

 moves 22 |5 degrees (a chordal dimension of 0.17 to 0.28 inch between the two pointers). 3) Make sure the flap bypass valve moves to the position 2.

 (d)  
Release the asymmetry test switch. 1) Make sure the asymmetry test light is off. 2) Make sure the flap bypass valve moves to the position 1.

 S 865-054
 (12)
 Make sure the flaps are in the fully retracted position.

 S 225-055

 (13)
 At each flap transmission, measure the angular clearance between the upstops on the ballscrew nut and the ballscrew yoke (Fig. 505).

 (a)  
Make sure the clearance is 170 to 190 degrees (1/2 turn |10 degrees).

 (b)  
At the No. 4 transmission, measure and make a record of the dimension X. Refer to this as the dimension X1.

 S 865-056
 (14)
 Supply the system B hydraulic power (AMM 27-51-00/201).

 S 725-057

 (15)
 Do a test to make sure the flaps move to the correct position:

 (a)  
Move the flap control lever to the UP detent to retract the flaps.

 (b)  
Move the flap control lever to the 1-unit detent to extend the flaps. 1) Stop for 2 minutes to permit the flap movement to stop.

 (c)  
At the No. 4 transmission, measure the dimension X. Refer to this as the dimension X2.

 (d)  
Make a record of the dimension X2 in Table 501 (EXTEND column).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 01 Page 524 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (e)  Measure and make a record of the dimension X2 with the flap control lever in the 2, 5, 10, 15, 25, 30 and 40-unit detents.
 ~.............................................................................. | Table 501 | ................................................................................
 |  FLAP  |  NO. 4 FLAP BALLSCREW POSITIONS  |
 |  CONTROL  |  -INCHES- |
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(159)