(c)  
Measure the play of the left hinge joint: 1) Slowly add and remove the two weights on the left

 stabilizer end near the front spar. 2) Set the dial indicator to zero 3) Move the two weights to the right stabilizer end.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-31
 ALL  ú ú 01 Page 601 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

(STABILIZER HINGE LINE) BODY STATION 1154  ELEVATOR 
HORIZONTAL STABILIZER  DIAL INDICATOR GAGE  TAIL CONE 
FWD 
SUPPORT ATTACHED TO FUSELAGE  BODY STATION 1156 

SEE B
SEE  A 
BODY STATION 1088 BULKHEAD (STRUCTURE)  FWD 
STABILIZER CENTER SECTION FITTING  A 
JACKSCREW SUPPORT FITTING 
SUPPORT 
FWD 
DIAL INDICATOR GAGE 
B 
Dial Indicator Gage Locations Figure 601 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-31
 ALL  ú ú 01 Page 602 ú Feb 20/84
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 4) Write down the value from the dial indicator. 5) Slowly remove the two weights. 6) Calculate the play of the left bearing:
 X = D - W Where D = value on the dial indicator W = 0.0000155 multiplied by the total of the two weights
 NOTE: If the quantity is negative, X = O
____
 (d)  Measure the play of the right hinge joint: 1) Attach the dial indicator to the right side. 2) Set the dial indicator to zero. 3) Slowly add the two weights to the left stabilizer end near
 the front spar. 4) Write down the value from the dial indicator. 5) Slowly remove the two weights. 6) Calculate the play of the right bearing:
 Y = D - W Where D = value on the dial indicator W = 0.0000155 multiplied by the total of the two weights
 NOTE: If the quantity is negative, Y = 0.
____
 S 976-004
 (2)  
Calculate the play of the stabilizer jackscrew joint (which is referred to as Z):

 (a)  
Make sure that the stabilizer is at 3 units of trim.

 (b)  
Open the 3701 access door.

 (c)  
Attach a dial indicator to the body station 1088 bulkhead structure. 1) Make sure the plunger pushes against the stabilizer lower

 surface at a minimum of 1/8 inch.
 2) Set the indicator to zero.

 (d)
Measure the free play of the stabilizer jackscrew joint:

 1)  Slowly add one weight each to the top surface of the left and the right stabilizer, adjacent to the fuselage along the stabilizer front spar.
 2) Write down the value from the dial indicator. 3) Slowly remove the weights.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-31
 ALL  ú ú 01 Page 603 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 4)  Calculate the play of the stabilizer jackscrew joint: Z = (D multiplied by 1.25) - (Wt multiplied by 1.25) Where D = value on the dial indicator Wt = 0.0000255 multiplied by the total of the two weights
 NOTE:____ If the quantity is negative, Z = 0.
 (3)  S 976-005Calculate the total stabilizer play (which is referred to as H): (a) Use the values X, Y, and Z to calculate H:
 X + Y H = ..... 2 + Z
 (4)  S 226-009Do a check of the X, Y, Z, and H dimensions: (a) If X is more than 0.060 inch, replace the left hinge bearing. (b) If Y is more than 0.060 inch, replace the right hinge bearing. (c) If Z is more than 0.05 inch, disassemble the stabilizer jackscrew (Ref 27-41-81/401), and repair the jackscrew, if it is necessary. (d) If H is more than 0.0505 inch, replace the stabilizer center section hinge bearings (Ref 27-41-31/401). 1) If it is necessary, disassemble and adjust the stabilizer jackscrew (Ref 27-41-81/401)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(100)