曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 22. Operation_________
 A.  The trailing edge flaps are normally actuated by a hydraulically operated drive system (Fig. 9). The drive system is controlled by a manually operated flap control lever located on the upper right side of the control stand. When the control lever is rotated, flap control cables displace the flap control unit linkage. This positions the trailing edge flap control valve to port pressurized fluid from hydraulic system B to the flap hydraulic motor. The hydraulic motor drives a torque tube system through a reduction gear train. The torque tubes drive two transmission assemblies at each flap. Ball bearing nuts and gimbal assemblies transfer rotary motion from the flap transmission assemblies into linear motion to extend the flaps. As the flaps extend, cables from the flap power unit follow-up cable drum rotate a flap control valve follow-up mechanism. A cam in the follow-up mechanism then displaces the trailing edge flap control valve slide. When the desired flap position is reached, the control valve closes to prevent flow of pressurized fluid to the flap hydraulic motor.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 01 Page 27 ú Mar 15/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 B.
C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
Retraction of the flaps due to airloads is prevented by a no-back friction brake in the inboard transmission assembly at each flap. If a transmission assembly should fail, a torque limiter in the remaining transmission assembly on that flap will stall the flap drive system to prevent structural damage. Stopping the drive system also prevents operation of the remaining flaps, thus maintaining the airplane in a normal flight attitude.The flap segments are mechanically separated during extension. As the flaps start to extend, an actuating mechanism moves the aftflap to form a slot between the aftflap and midflap. At about 8 units of midflap extension, the foreflap sequencing toggles contact stops on the main flap tracks. The stops prevent additional aft movement of the foreflap. Continued midflap extension creates a slot between the foreflap and midflap. As the midflap approaches full travel, the aftflap again moves relative to the midflap, increasing the width of the slot between the two segments.A flap alternate drive unit is provided to operate the trailing edge flaps electrically if a failure prevents normal hydraulic operation. The flap alternate drive unit is controlled from two switches located on the overhead panel. The alternate flaps arm switch and control switch operate the system. Actuation of the alternate flaps arm switch to ARM supplies 28-volt dc power to the alternate flaps control switch. Simultaneously, 28-volt dc power is supplied to position the trailing edge flap bypass valve to BYPASS. This interconnects the flap hydraulic motor ports to allow circulation of hydraulic fluid and prevents fluid flow from the control valve to the hydraulic motor. Actuation of the alternate flaps control switch to DOWN energizes the alternate flap down relay to complete a circuit to extend the flaps. When the flaps are fully extended, a down limit switch opens to break circuit continuity. Positioning the alternate flaps control switch to UP closes the alternate flap up relay to complete a circuit to retract the flaps. When the flaps are fully retracted, an up limit switch opens to break circuit continuity. The trailing edge flaps may be stopped in any intermediate position by returning the alternate flaps control switch to OFF.An electrical asymmetry system will stop operation of the flap drive system when a certain separation of left and right indicator pointers occurs. The separation closes a comparator switch in the indicator to operate the flap asymmetry relay, causing the hydraulic bypass valve to stop operation of the flap drive hydraulic motor.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-51-00
 ALL  ú ú 01 Page 28 ú Jul 15/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 F.  A flap control cable tension switch system is provided to stop operation of the flap drive system if a flap control cable breaks. If a cable should break, the spring loaded lever supporting the cable pulley moves the lever mounted magnet away from the switch. This activates the switch circuit. The activated switch provides 28-volt dc power to activate the flap bypass valve to BYPASS. This shuts off hydraulic power to the hydraulic motor. The flaps are prevented from extending beyond the flap control lever position.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(143)