S 084-041

 (17)
 Remove rig pins R-3 and R-4 from the forward quadrants.

 S 224-042

 (18)
 Do these steps to make sure the rudder pedals have the correct travel:

 (a)  Make sure the rudder trim indicator is at zero units of trim.
 (b)  Turn the rudder pedal adjustment crank to move the rudder
 pedals full forward.
 (c)  Do these steps to set the pedal to the middle position:
 1)  Turn the rudder pedal adjustment crank to move the rudder
 pedals full aft.  Keep a record of the number of turns.
 2)  Turn the rudder pedal adjustment crank "half" the recorded
 number of turns forward.  Mark this position as "position
 1" at the pedal pivot points on both the Left and Right
 pedals.
 NOTE:____ You must measure the distance shown below from
 this location.
 (d)  Adjust the rudder pedals to the fully forward position.
 (e)  Push the left rudder pedal forward until the forward quadrant
 touches its stop (this is referred to as position 2 for the
 left rudder pedal).
 NOTE:____ Push the right rudder pedal forward to get position 2
 for the right rudder pedal.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-31
 ALL  ú ú 03 Page 408 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (f)  Measure the distance (at the piviot of the rudder pedal) from position 1 to position 2.
 NOTE: You must measure this distance for the left and the
____
 right rudder pedals.

 1)  Make sure the distance from position 1 to position 2 is a minimum of 6.86 inches.
 (g)  
Adjust the rudder pedals to the fully aft position.

 (h)  
Push the LEFT rudder pedal forward until the forward quadrant touches its stop (this is referred to as position 3 for the RIGHT rudder pedal).

 NOTE: Push the right rudder pedal forward to get position 3
____
 for the left rudder pedal.

 (i)  Measure the distance (at the piviot for the rudder pedal) from position 1 to position 3.
 NOTE: You must measure this distance for the left and the
____
 right rudder pedals.

 1)  Make sure the distance from position 1 to position 3 is a minimum of 6.89 inches.
 E.  Put the Airplane Back to Its Usual Condition
 S 414-006
 (1)  
Install the access panels that you removed.

 (2)  
Close the forward access door.

 S 414-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-31
 ALL  ú ú 01 Page 409 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 RUDDER PEDAL ADJUSTMENT CRANK - REMOVAL/INSTALLATION
____________________________________________________
 1.  General
_______
 A.  This procedure contains the removal task and the installation task for the rudder pedal adjustment cranks. These tasks are applicable to the captain's or the first officer's cranks.
 TASK 27-21-41-024-001
 2.  Rudder Pedal Adjustment Crank Removal
_____________________________________
 A.  References
 (1)  
12-31-11/201, Access Doors

 B.  
Access

 (1)  
Location Zones
 202 Lower Nose Compartment

 (2)  
Access Panel
 1103 Forward Access Door

 C.  
Procedure (Fig. 401)

 S 014-002
 (1)  
Open the access door 1103 to get access to the lower nose compartment (Ref 12-31-11/201).

 S 014-003

 (2)  
Remove the overhead access panels in the forward part of the lower nose compartment to get access to the rudder jackshaft.

 S 034-004

 (3)  
Disconnect the bottom part of the cable:

 (a)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(49)