EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-00
 ALL  ú ú 01 Page 503 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
FWD  JACKSHAFT 
YOKE 
CAPTAIN'S 
BUSROD (TO THE FIRST  FORWARD 
OFFICER'S QUADRANT)  QUADRANT 
FORWARD  SEE  A 
QUADRANT 

PUSHROD
PUSHROD CABLE GUARD BLOCK
RIG PIN AT THE FORWARD RIG PIN HOLE
PUSHROD TO THE NOSE WHEEL (R-3 AT THE CAPTAIN'S FORWARD QUADRANT)
STEERING (ON THE CAPTAIN'S QUADRANT STOP (R-4 AT THE FIRST OFFICER'S FORWARD QUADRANT)
QUADRANT ONLY)
SEEB CAPTAIN'S FORWARD QUADRANT
A
FORWARD QUADRANT
STOP QUADRANT  FWD 
QUADRANT STOP 
B 
Figure 502 Rudder Pedal Adjustment 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-00
 ALL  ú ú 01 Page 504 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 WARNING: MAKE SURE YOU RELEASE THE CABLE TENSION BEFORE
_______ YOU ADJUST THE BUS ROD. IF THE CABLE TENSION IS NOT CORRECT, IT CAN CAUSE DAMAGE TO THE CABLE AND INJURY TO PERSONS.
 a) Loosen the turnbuckles in the stabilizer jackscrew
 compartment to release the cable tension. b) Remove the bus rod from the jackshaft yoke. c) Install the rig pins R-3 and R-4 in the forward holes
 in the forward quadrants. d) Adjust the bus rod until you can install the bolts
 freely through the jackshaft yoke. e) Install the washers, spacer, nuts, and cotter pins. f) If it is necessary, adjust the pushrod to the nose
 wheel steering (Ref 32-51-00/501).
 (e)  
Make sure that the tolerance between the cable guard block and the forward quadrant is 0.03-0.05 inch.

 (f)  
Remove the rig pins R-3 and R-4.

 (g)  
Move the captain's forward quadrant until you can install the rig pin R-3 through the aft hole in the forward quadrant. 1) Make sure that the tolerance between the quadrant and the

 quadrant stop is less than 0.06 inch.
 2) Remove the rig pin R-3.

 (h)  
Move the first officer's forward quadrant until you can install the rig pin R-4 through the aft hole in the forward quadrant. 1) Make sure that the tolerance between the quadrant and the

 quadrant stop is less than 0.06 inch.
 2) Remove the rig pin R-4.

 S 825-020
 (3)  
Adjust the rudder pedals:

 (a)  
Install the rig pin R-5.

 (b)  
Move the forward quadrants until you can install the rig pins R-3 and R-4 in the forward holes in the forward quadrant.

 (c)  
Make sure that you can install the rig pins R-1 and R-2 freely on the pedal arm assembly. 1) If you can not install the rig pins, adjust the rudder

 quadrant pushrods: a) Loosen the jamnuts on one or two ends of the rod assembly. b) Turn the tube to get the correct length.
 NOTE: The length given of the tension rod is 36.50
____
 inches.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-00
 ALL  ú ú 01 Page 505 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

CAPTAIN'S RUDDER PEDALS
(THE FIRST OFFICER'S RUDDER PEDALS ARE ALMOST THE SAME)

Rudder Forward Quadrant Adjustment
Figure 503

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(18)