(j)  
Remove hydraulic power from rudder systems A and B if it is not necessary (AMM 27-21-00/201).

 (4)  
Remove electrical power if it is not necessary (AMM 24-22-00/201).

 S 864-014
 TASK 27-11-94-204-023
 9.  Rudder Trim Knob and Lightplate Check_____________________________________
 A. References
 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 27-21-00/201, Rudder and Rudder Trim Control System

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-94
 ALL  ú ú 02 Page 408 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 B.  Access
 (1)  
Location Zone
 101 Control Cabin, LH
 102 Control Cabin, RH

 C.  
Procedure

 S 864-024
 (1)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6-2 Circuit Breaker Panel
 1) RUDDER TRIM INDICATOR
 2) AILERON TRIM CONTROL
 3) RUDDER TRIM CONTROL

 S 224-025
 (2)  
Do a check of the rudder trim knob and lightplate:

 (a)  
Remove the rudder trim knob from the switch shaft.

 (b)  
Put the knob fully down on the switch shaft.

 (c)  
Make sure the rudder trim knob is 0.010-0.050 inch from the top of the lightplate.

 NOTE: Measure the clearance while you push the knob against
____
 the plate.

 1)  If it is necessary, adjust the switch shaft height:
 a)  Use a mixture of shims or washers to get the necessary dimension between the switch shaft and the baseplate (Detail A).
 (d)  Tighten the set screw in the knob.
 S 864-026
 (3)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6-2 Circuit Breaker Panel
 1) RUDDER TRIM INDICATOR
 2) AILERON TRIM CONTROL
 3) RUDDER TRIM CONTROL

 (4)  
Supply electrical power (AMM 24-22-00/201).

 S 714-028

 (5)  
Do a test on the rudder trim:

 (a)  
Supply hydraulic power to the rudder trim systems A and B (Ref 27-21-00/201).

 (b)  
Make sure the rudder trim indicator is at 0 +/-0.25 units.

 (c)  
Make sure the rudder is at the neutral position.

 (d)  
Turn the rudder trim knob to NOSE LEFT until the mark on the trim knob aligns with the indicator mark on the control stand.

 (e)  
Make sure the rudder does not move.

 S 864-027
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-94
 ALL  ú ú 03 Page 409 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (f) (g) (h) (i)  Turn the rudder trim knob to NOSE RIGHT until the mark on the trim knob aligns with the indicator mark on the control stand.Make sure the rudder does not move.Make sure the rudder trim knob operates smoothly.Make sure the rudder trim knob goes back to the center freely.
 (6)  S 864-001Remove electrical power if it is not necessary (AMM 24-22-00/201).
 (7)  S 864-031Make sure the rudder trim knob does not rub on the lightplate.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-11-94
 ALL  ú ú 02 Page 410 ú Jul 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 RUDDER AND RUDDER TRIM CONTROL SYSTEM - DESCRIPTION AND OPERATION
_________________________________________________________________
 1.  General_______
 A.  Yaw control of the airplane is provided by a single conventional rudder without tab. There are two separate hydraulic systems powering one main power control unit. Rudder control backup is provided by a standby power unit, which is driven by a third hydraulic system. Any one of the three hydraulic systems will provide effective rudder control. Rudder trim is accomplished by operating a trim control knob which repositions the rudder centering unit.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(4)