(6)  
Apply some of the sealant to the jumper ends and bolts.

 S 624-016
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-21
 ALL  ú ú 02 Page 406 ú Mar 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 764-024
 (7)  Use the milliohmmeter to make sure there is a maximum of 0.010 ohms
 between the rudder and the vertical fin.
 S 624-017
 (8)  Apply some of the corrosion preventive compound to the hinges before
 you install them.
 S 434-018
 (9)  Install the hinge bolt, countersunk washer, and the nut that
 connects the fin hinge segment to the bearing bar.
 (a) HINGES 1 AND 2;
 Tighten the hinge bolt to 95 to 110 pound-inches.
 (b) HINGES 3, 4, 5, 6, AND 7;
 Tighten the hinge bolt to 60 to 85 pound-inches.
 (c) Continue to turn the nut until it aligns with the cotter pin
 hole.
 NOTE: For hinges 1 and 2, the maximum permitted torque is 190____
 pound-inches.
 For hinges 3, 4, 5, 6, and 7, the maximum permitted
 torque is 140 pound-inches.
 (d) Install the cotter pin in the bolt.
 S 824-019

 (10)
 HINGE 2; Install shims between the bearing bar and the rudder hinge segment (2 locations).

 (a)  
Make sure the clearance between the bearing bar and the rudder hinge segment is less than 0.005 inch.

 NOTE: Measure the clearance before you tighten the bolts.
____
 S 434-020
 (11)
 Tighten the bolts that connect the bearing bar to the rudder.

 (a)  
HINGES 1 AND 2; Tighten the bolts for the bearing bars to 90 to 160 pound-inches.

 (b)  
HINGES 3, 4, 5, 6, AND 7; Tighten the bearing bar bolts to 60 to 95 pound-inches.

 S 414-021
 (12)
 Install the applicable hinge coverplates.

 S 094-022

 (13)
 Remove rig pin R-3.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-21
 ALL  ú ú 08 Page 407 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STANDBY RUDDER ACTUATOR - REMOVAL/INSTALLATION
______________________________________________
 1.  General_______
 A.  This procedure gives the instructions to remove and install the standby rudder actuator (referred to as the actuator).
 TASK 27-21-24-004-001
 2.  Standby Rudder Actuator Removal_______________________________
 A.  Special Tools and Equipment
 (1)  F70207-93 Rig Pin Kit:
 -------------------------------------------------------------------| | | DIAMETER | LENGTH | | | REF NO. | F70207-| (INCHES) | (INCHES) | FUNCTION | -------------------------------------------------------------------| R-5 | -11 | 0.309-0.311 | 6.7 -0.25 | RUDDER FEEL AND | | | | | | CENTERING UNIT | -------------------------------------------------------------------
B.  References
 (1)  
27-21-00/201 Rudder and Rudder Trim Control System

 C.  
Access

 (1)  
Location Zones
 706 Vertical Fin
 708 Rudder

 (2)  
Access Panels
 9515L TE Access Panel - Rudder
 9528R Access Door - Rudder
 9529R Access Door - Rudder
 9555R Cover - Rudder Nose
 9556L Cover - Rudder Nose

 D.  
Prepare for the Removal

 (1)
Remove hydraulic power from the rudder (Ref 27-21-00/201).

 S 014-003

 (2)  
Remove the access panels on the left side of the vertical fin for access to the standby rudder actuator.

 S 494-004

 (3)  
Install rig pin R-5 in the feel and centering unit for the rudder (Ref 27-21-00/501).

 S 864-002
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(40)