E.
Adjust the Standby Rudder Actuator

 S 825-007
 (1)  
If the index mark on the input crank does not align within +/-0.02 inch of the center index mark on the standby rudder actuator, adjust the input rod (Fig. 501):

 (a)  
Loosen the two locknuts on the input rod.

 (b)  
Remove the bolt that connects the input rod to the input crank.

 (c)  
Turn the aft rod end and the input rod together or turn the aft rod end only until the index marks align.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-24
 ALL  ú ú 01 Page 503 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

RUDDER

Rudder Travel And Index Plate
Figure 502

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-24
 ALL  ú ú 01 Page 504 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

Steering Depressurization Valve
Figure 503

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-24
 ALL  ú ú 01 Page 505 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (d)  
Connect the input rod to the input crank.

 (e)  
Supply the rudder hydraulic power systems A and B (Ref 27-21-00/201).

 S 825-009
 (2)  
If the index mark on the input crank does not align within +/-0.02 inch of the center index mark on the standby rudder actuator, adjust the input rod (Fig. 501):

 (a)  
Loosen the two locknuts on the input rod.

 (b)  
Turn the input rod until the index marks align.

 (c)  
Tighten the two locknuts on the input rod.

 S 865-010
 (3)  
Make sure you can see the threads on the rod ends through the inspection holes in the input rod.

 S 095-011

 (4)  
Remove the rig pin R-5.

 S 735-012

 (5)  
Do a test of the standby rudder actuator.

 TASK 27-21-24-735-013
 3. Standby Rudder Actuator Test
____________________________
 A. References
 (1)  
27-21-00/201, Rudder and Rudder Trim Control System

 (2)  
32-00-01/201, Ground Lock Assemblies

 B.
Access

 (1)  
Location Zones
 706 Vertical Fin
 708 Rudder

 C.
Prepare for the Test

 S 045-014
 (1)  Install the lockout pin for the nose gear steering (Fig. 503) (Ref 32-00-01/201).
 NOTE: It is not necessary to install the lockout pin if the
____ airplane is on jacks and the nose landing gear is fully extended.
 S 865-015
 (2)  
Supply the rudder hydraulic power systems A and B
 (Ref 27-21-00/201).

 (3)  
Set the rudder trim to zero units of trim.

 (4)  
Make sure the rudder is in its neutral position.

 S 865-016
 S 215-017
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-24
 ALL  ú ú 02 Page 506 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 865-018
 (5)  
Put the FLT CONTROL A and B switches to OFF.

 S 865-019

 (6)  
Put the FLT CONTROL A and B switches to STDBY RUD.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(43)