F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
78-32-41-860-001 Manual Deployment of the Blocker Door
 78-32-42-000-001 Removal of the Ramp Fairing
 78-32-42-400-001 Installation of the Ramp Fairing
 78-36-00-010-040 Opening of the Thrust Reverser Doors
 78-36-00-410-040 Closing of the Thrust Reverser Doors
 78-32-42-991-301 Fig. 601

 3. Job Set-up
__________
 Subtask 78-32-42-941-050

 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-32-42-010-050
 B. Get Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put the access platform in position.
 Subtask 78-32-42-040-050

 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 F 『 EEFF : ALL E Page 60278-32-42
 E E Feb 01/98 E E ECES E Subtask 78-32-42-860-050

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 D. Manually move the blocker door to the open position (Ref. TASK 78-32-41-860-001).
 Subtask 78-32-42-480-051
 E. Install the SAFETY SLEEVE - PIVOTING DOOR ACTUATOR (HIX3005) on the
 blocker door actuator (Ref. TASK 78-32-41-480-001).

 Subtask 78-32-42-010-051
 F. Open the thrust reverser cowl doors (Ref. TASK 78-36-00-010-040):
 FOR 1000EM1
 451AL, 452AR.
 FOR 1000EM2
 461AL, 462AR.

 4. Procedure
_________
 (Ref. Fig. 601/TASK 78-32-42-991-301)
 Subtask 78-32-42-210-050
 A. Do a Visual Inspection of the Ramp Fairing
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the ramp fairing for :
 A. Damage  No damage permitted If you find some damage, replace the defective part (Ref. TASK 78-32-42-000-001) and (Ref. TASK 78-32-42-400-001)
 B. Crack 1 in. (25.4 mm) maximum  Seal damaged area from
 length in any direction  entrance of moisture with aerodynamic tape (Material No. CP2517)
 F 『 EEFF : ALL E Page 60378-32-42
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

 Ramp Fairing
 Figure 601/TASK 78-32-42-991-301- 12 (SHEET 1)
 F EEFF :  ALL  『E 78-32-42 Page 604 
E  E  Feb 01/98
 E  E
 ECES  E

 Ramp Fairing
 Figure 601/TASK 78-32-42-991-301- 22 (SHEET 2)
 F EEFF :  ALL  『E 78-32-42 Page 605 
E  E  Feb 01/98
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Hole
D. Delamination
7.4 in. (187.96 mm) minimum separation between other cracks, holes and delaminations
 Five cracks maximum per ramp fairing
1 in. (25.4 mm) maximum diameter
7.4 in. (187.96 mm) minimum separation between other holes, cracks and delaminations
 Five holes maximum per ramp fairing
1.5 in. (38.1 mm) maximum length
 7.4 in. (187.96 mm) minimum separation between other delaminations, holes and cracks
 Five delaminations maximum per ramp fairing Monitor at "A" check
If more than maximumlimits, replace the ramp fairing (Ref. TASK 78-32-42-000-001) and (Ref. TASK 78-32-42-400-001)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(87)