F 『
 E C F M E
 E E
 E 56-5B E
 E E
 C. Referenced Information

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
 Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 78-31-49-991-317 Fig. 416
 3. Job Set-up
__________
 Subtask 78-31-49-860-096
 A. Aircraft Maintenance Configuration
 (1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.

 (2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).

 (3) Make sure that the access platform is in position.

 Subtask 78-31-49-010-152
 B. Get Access
 (1) Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 F 『 EEFF : ALL E Page A44078-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (2) Make sure that the thrust reverser doors are open: (Ref. TASK 78-36-00-010-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
 Subtask 78-31-49-040-130
 C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
 4. Procedure
_________
 (Ref. Fig. 416/TASK 78-31-49-991-317) Subtask 78-31-49-420-087
 A. Installation of the Left or Right Inner Supply Pipe of the Door-Opening Actuator
 (1) Remove the protective covers from the pipe ends.

 (2) Put the inner supply pipe in position on the forward frame.

 (3) Attach the inner supply pipe to the upper and lower brackets with the nuts.

 (4) TORQUE the nuts to between 70 and 80 lbf.in (0.79 and 0.90 m.daN).

 (5) Connect the supply pipe to both ends of the inner supply pipe.

 (6) TORQUE the coupling nuts to between 130 and 150 lbf.in (1.46 and 1.69 m.daN).

 (7) Attach the supply pipe to the forward frame with the clamps and bolts.

 (8) TORQUE the bolts to between 70 and 80 lbf.in (0.79 and 0.90 m.daN). NOTE : Apply a witness line of finish paint EA4 blue 5991 (Material

____ No. CP2245) on all nuts and connections after they are torqued.
 F 『 EEFF : ALL E Page A44178-31-49
 E E Feb 01/98 E E ECES E 5. Close-up

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

________ Subtask 78-31-49-410-103
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the thrust reverser doors: (Ref. TASK 78-36-00-410-040) FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR

 Subtask 78-31-49-440-092
 B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 78-31-49-410-104
 C. Close Access
 (1) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Remove the access platform(s).

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page A44278-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 TASK 78-31-49-000-002

 Removal of the Lock-Out Bolt Storage Bracket
 WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
 WORK ON PRESSURIZED SYSTEMS.

R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
 ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
 COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.

 1. Reason for the Job

__________________
 Self Explanatory

 2. Job Set-up Information
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 2(2)